IronRidge Flush Mount Manual

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - I

INSTALLATION MANUAL

XR FLUSH MOUNT

INSTALLATION MANUAL

CONTENTS

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 1

DISCLAIMER 1

RATINGS 2

MARKINGS 2

ATTACHMENTS 3

COMPONENTS 4

1. ATTACH BASES 5

2. PLACE RAILS 5

3. SECURE LUGS 6

4. SECURE MODULES 6

CAMO 7

BONDING JUMPER 7

EXPANSION JOINTS 8

ELECTRICAL DIAGRAM 9

COMPOSITION SHINGLE 10-12

TILE 13-15

ADDITIONAL ROOF TYPES 15

LOW SLOPE ROOFS 16

CONDUIT PENETRATION 17

CONDUIT MOUNT 18

END CAPS 19

WIRE CLIPS 19

JAYBOX 19

MICROINVERTER KITS 20

SYSTEMS USING ENPHASE MICROINVERTERS OR SUNPOWER AC MODULES 20

SYSTEMS USING MICROSTORAGE PRODUCTS 21

FRAMELESS MODULE KITS 21

CONTOUR 22

MODULE COMPATIBILITY 23-29

FRAMELESS MODULE COMPATABILITY 30

DISCLAIMER

This manual describes proper installation procedures and provides necessary standards required for product reliability.

Warranty details are available on website. All installers must thoroughly read this manual and have a clear understanding

of the installation procedures prior to installation. Any installation or use of this product not in accord with or not authorized

by this written instruction shall void any and all warranties, express or implied, on the product or the use of the product

and may cause failure, property damage and personal injury. IronRidge is not liable for any unauthorized use. Install and

use only with other IronRidge products to ensure proper t and function.

IT IS THE INSTALLER’S RESPONSIBILITY TO:

• Ensure safe installation of all electrical aspects of the array. All electrical installation and procedures should be

conducted by a licensed and bonded electrician or solar contractor. Routine maintenance of a module or panel shall

not involve breaking or disturbing the bonding path of the system. All work must comply with national, state and local

installation procedures, product and safety standards.

• Comply with all applicable local or national building and re codes, including any that may supersede this manual.

• Ensure all products are appropriate for the installation, environment, and array under the site’s loading conditions.

• Use only IronRidge parts or parts recommended by IronRidge; substituting parts may void any applicable warranty.

• Review the Design Assistant and Certication Letters to conrm design specications.

• Ensure provided information is accurate. Issues resulting from inaccurate information are the installer’s responsibility.

• Ensure bare copper grounding wire does not contact aluminum and zinc-plated steel components, to prevent risk of

galvanic corrosion.

• If loose components or loose fasteners are found during periodic inspection, re-tighten immediately. Any components

showing signs of corrosion or damage that compromise safety shall be replaced immediately.

• Provide an appropriate method of direct-to-earth grounding according to the latest edition of the National Electrical

Code, including NEC 250: Grounding and Bonding, and NEC 690: Solar Photovoltaic Systems.

• Disconnect AC power before servicing or removing modules, AC modules, microinverters and power optimizers.

• Review module and any 3rd party manufacturer’s documentation for compatibility and compliance with warranty terms

and conditions.

• Ensure that the roof is in good condition prior to instaling any IronRidge components.

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 2

RATINGS

Product markings are located on the Grounding Lug bolt

head.

MARKINGS

UL 2703 LISTED

Conforms to UL STD 2703 Standard for Safety First Edition: Mounting Systems, Mounting Devices, Clamping/

Retention Devices, and Ground Lugs for Use with Flat-Plate Photovoltaic Modules and Panels

• Scope of Evaluation includes bonding, grounding, mechanical loading, and re classication

• Max Overcurrent Protective Device (OCPD) Rating: 40A

• Max Module Size: 30.5 ft²

• Module Orientation: Portrait or Landscape

• System Design Load Rating: 10 PSF downward, 5 PSF upward, 5 PSF lateral

• Actual system structural capacity including spans and cantilevers are dened by PE stamped certication letters

• CAMO Specic Design Load rating: 50 PSF downward, 50 PSF upward, 15 PSF lateral

Certied to CSA TIL No. A-40 Photovoltaic Module Racking Systems

• Load Rating: 2400 PA [50 PSF]

CLASS A SYSTEM FIRE RATING PER UL 2703

• Any Roof Slope with Module Types 1, 2, 3, 13, 19, 25, 29 and 38: Allowed with any roof slope. Any module-to-roof gap

is permitted, with no perimeter guarding required

• Module Types 4 and 5: Allowed with Steep Slope Roofs (≥ 9.5°). Any module-to-roof gap is permitted, low edge

guarding (Trim) required

• Class A rated PV systems can be installed on Class A, B, and C roofs without aecting the roof re rating

CLASS B SYSTEM FIRE RATING PER UL 2703

• Module Types 4 and 5: Allowed with Steep Slope Roofs (≥ 9.5°). Any module-to-roof gap is permitted, with no

perimeter guarding required.

WATER SEAL RATINGS:

• UL 441 and TAS100(A) (Flashfoot2, L-Mount, Flashvue, All Tile Hook, Knockout Tile, Halo UltraGrip)

• Tested and evaluated without sealant

• Any roong manufacturer approved sealant is allowed.

• Ratings applicable for steep roof slopes 2:12 and above.

UL 2703A RATINGS:

• Conforms to UL SUBJECT 2703A - Halo UltraGrip and BUG

• Steep Slope Ratings applicable for Asphalt Shingle roofs with slopes 2:12 and up

• Low Slope Ratings applicable for Roll Roong (Rolled Comp) roofs with slopes 1:12 and up

• Low Slope Ratings applicable for Modied Bitumen (Mod-Bit) roofs with slopes 1/4:12 and up

• Installer must verify roof slope prior to installing HUG or BUG to validate applicable roof types

UL 1565 RATINGS:

• Conforms to UL STD 1565 and Certied to CSA C22.2 #18.5-13 Positioning Devices - Wire Clip

• Operating Temperature Range: -35 to 90C

• Maximum Load: 10lbs

• For outdoor use

STRUCTURAL CERTIFICATION

• Designed and Certied for Compliance with the International Building Code & ASCE/SEI-7

FLORIDA PRODUCT APPROVAL #FL29843

• Approved for installation both inside and outside High Velocity Hurricane Zones (HVHZ)

• Additional details and full list of approved components can be found here

#5003807

#5028987

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 3

ATTACHMENTS

BONDING HARDWARE TORQUE VALUES

Please refer to each attachment's individual section for full details

on all torque values and instructions.

☐ 3/8" Bonding Hardware Nuts (7/16" Socket): 250 in-lbs

☐ All Tile Hook Carriage Bolts (7/16" Socket): 132 in-lbs

☐ Flat Tile Hook Carriage Bolts (7/16" Socket): 132 in-lbs

☐ Flat Roof Attachment Nuts (9/16” Socket): 250 in-lbs

☐ Lynx Set Screw (3/16" Hex Drive): 150 in-lbs

☐ Lynx Flange Nut (1/2" Socket): 150 in-lbs

➢ If using previous version of Integrated Grounding Mid Clamps,

End Clamps, Expansion Joints, Classic Composition Mount

and for a list of approved 3rd party components please refer to

Alternate Components Addendum (Version 2.1)

ATTACHMENTS

QM L-MountFlashVue

QM Quick Hook and

Flashing (optional)

QM QBase Tile

A A

B B

C C

D D

E E

F F

All Tile Hook and

Flashing (optional)

FlashFoot2

COMPOSITION SHINGLE

TILE

QM Tile Replacement

QM QBase

QM QBase MountFlat Roof Attachment

LOW SLOPE ROOF

QM Qbase Shake -

Slate - Metal Shingle

ADDITIONAL ROOF TYPES

PRE-INSTALLATION

☐ Verify module compatibility. See Page 21 for info.

TOOLS REQUIRED

☐ Cordless Drill (non-impact)

☐ Impact Driver (for lag bolts)

☐ Torque Wrench (0-250 in-lbs)

☐ 7/16” Socket

☐ 1/2" Socket

☐ 9/16" Socket

☐ 7/32" Drill Bit

☐ 3/8" Socket

☐ 1/8" Drill Bit

☐ 1/4" Drill Bit

☐ T30 Bit

☐ Channel Lock Pliers

☐ #3 Phillips Bit

☐ 3/16" Hex Bit

QM Lynx Metal Roof

Attachment

QM Tile Conduit

Penetration

Knockout Tile

HUG

(Halo UltraGrip)

Flat Tile Hook and

Flashing (optional)

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 4

COMPONENTS

BONDING HARDWARE TORQUE VALUES

Please refer to each attachment's individual section for full details

on all torque values and instructions.

☐ Universal Fastening Object (7/16" Socket): 80 in-lbs

☐ End Fastening Object (7/16" Socket): 80 in-lbs

☐ Rail Grounding Lug Nut (7/16" Socket): 80 in-lbs

☐ Module Grounding Lug

☐ Grounding Nut (7/16" Socket): 60 in-lbs

☐ Grounding Lug Terminal Screws (7/16" Socket): 20 in-lbs

☐ Microinverter Kit Nuts (7/16" Socket): 80 in-lbs

☐ Frameless Module Kit Nuts (7/16" Socket): 80 in-lbs

☐ 3/8" Bonding Hardware Nuts (7/16" Socket): 250 in-lbs

☐ Contour Clamp (T-30 Torx Bit): 80 in-lbs

➢ Unless otherwise noted, all components have been evaluated for

multiple use. They can be uninstalled and reinstalled in the same

or new location.

COMPONENTS

XR Rail

UFO and Stopper

Sleeve (30-46MM)

CAMO

Rail Grounding Lug

8" Bonding Jumper

Single Use Only

End Cap

JAYBOX

3/8" Bonding

Hardware

Microinverter Kit

Frameless Module Kit

Frameless

End/Mid Clamp

QM Classic Conduit

Comp Mount

QM Tile Conduit

Mount

PRE-INSTALLATION

☐ Verify module compatibility. See Page 21 for info.

TOOLS REQUIRED

☐ Cordless Drill (non-impact)

☐ Impact Driver (for lag bolts)

☐ Torque Wrench (0-250 in-lbs)

☐ 7/16” Socket

☐ 1/2" Socket

☐ 9/16" Socket

☐ 7/32" Drill bit

☐ 1/8" Drill bit

☐ 1/4" Drill bit

☐ T30 Torx Bit

☐ Channel Lock Pliers

☐ #3 Phillips Bit

☐ Paddle Bit

BOSS

Module Grounding

Lug

Wire Clip

Contour Trim

Contour Clamp

QM Composition

Conduit Penetration

L-Foot

EFO (30-40mm)

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 5

1. PLACE ATTACHMENTS

A. CONNECT SPLICES

Use BOSS(Bonded Structural Splice), as needed, to join multiple sections of Rail.

BOSS - Bonded Structual Splice

Insert BOSS into rst Rail up until the Stop Tab. Slide second Rail fully into place.

➢ Rows using BOSS and exceeding 100 of rail for all roof attachments (60 feet

when using HUG) must use Expansion Joints.

➢ Boss Splices may be installed in any location within a span.

➢ UFO and Bonding Hardware must be installed 1" away from the point where

two Rails join together.

B. PREPARE HARDWARE

Slide square-headed bolts into side-facing rail slot. Space out bolts to match

attachment spacing.

➢ Tape ends of rail, to keep bolts from sliding out while moving.

➢ If using T-

bolts, carry hardware onto roof and proceed.

C. ATTACH RAILS

Drop rail with hardware into roof attachment. Level rail at desired height, then torque to

250 in-lbs.

➢ Rail can face either upslope or downslope on roof.

➢ When using attachments with longer slots, do not install Rail lower than the

top of the L-Foot to avoid damage to modules.

2. PLACE RAILS

Tested or evaluated third-party roof attachments:

• S-5! Metal Roof Clamps - Certication of metal roof clamps

includes bonding to both painted and galvalume metal roofs.

Follow all instructions and installation practices outlined by S-5! in their Resources Page.

• EcoFasten Green Fasten GF-1 Anchors

The general installation method for attachments is to

locate a rafter, drill a pilot hole and install the attachment.

For composition roof attachments installation instructions

refer to page 10. For tile roof attachments refer to page

12. For low slope roof attachments refer to page 14.

When using approved third party attachments, refer to

manufacturer's install instructions.

Torque to

250 in-lbs

Preload and Space

Square Bolts

BOSS

Insert Rail untill fully seated

against Stop Tab

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 6

3. SECURE LUGS

Use with one solid or stranded copper

wire, conductor size 10-4AWG.

4. SECURE MODULES

A. SECURE FIRST END

Place rst module in position on rails, a minimum of 1”

from rail ends. Snap Stopper Sleeves onto UFO. Fasten

module to rail using the UFO with stopper sleeve or EFO,

ensuring that the clamp is hooked over the top of the

module. Torque to 80 in-lbs.

➢ Ensure rails are square before placing modules.

➢ Hold Clamps on end while torquing to prevent rotation.

➢ If using CAMO instead of UFO + Stopper Sleeve, refer to Page 19

for CAMO installation procedure.

➢ UFO can be installed on modules 30 to 46mm.

➢ EFO can be installed on modules 30 to 40mm.

B. SECURE NEXT MODULES

Place UFO into each rail, placing them ush against rst

module. Slide second module against UFO. Torque to 80

in-lbs. Repeat for each following module.

➢ When reinstalling UFO, move modules a minimum of 1/16" so

UFOs are in contact with a new section of module frame.

➢ When UFOs are loosened and re-tightened, ensure UFO T-bolt

bottoms out in rail channel before re-torquing UFO to achieve full

engagement between T-bolt and rail.

➢ If using Wire Clips, refer to Page 18.

C. SECURE LAST END

Place last module in position on rails, a minimum of 1”

from rail ends. Snap Stopper Sleeves onto UFO. Secure

UFO with Stopper Sleeve or EFO on rails, ensuring they

are hooked over top of module. Torque to 80 in-lbs.

➢ Hold clamps on end while torquing to prevent rotation.

➢ Repeat all steps for each following row of modules, leaving a

minimum 3/8" gap between rows

➢ If using CAMO instead of UFO + Stopper Sleeve/EFO, refer to

Page 19 for CAMO installation procedure.

1" From

Rail End

UFO or EFO

(80 in-lbs)

Stopper

Sleeve

or EFO

UFO

(80 in-lbs)

UFO

(80 in-lbs)

Terminal Screw

(20 in-lbs)

Hex Nut

(80 in-lbs)

Grounding Lugs

Only one Grounding Lug (Rail or Module) required per continuous

subarray, regardless of subarray size (Unless frameless modules are

used, see Page 20).

➢ Grounding Lugs are intended to for use with one solid or

stranded copper wire, conductor size 10-4 AWG.

Rail Grounding Lug

Insert T-bolt in Top Rail slot and torque Hex Nut to 80 in-lbs. Install

a minimum 10 AWG solid copper or stranded grounding wire. Torque

terminal screw to 20 in-lbs.

➢ Module Grounding Lugs can be installed anywhere along the Rail

and in either orientation shown.

Module Grounding Lug

Insert Bolt through Manufacturer approved grounding location and torque

Hex nut to 60 in-lbs. One Module Grounding Lug may be installed to

one module per row. Install a minimum 10 AWG solid copper or stranded

grounding wire. Torque terminal screw to 20 in-lbs.

➢ Refer to module manufactuer for mounting location and

instructions.

FLANGE NUT

GROUNDING LUG

BOLT

STAR WASHER

Terminal Screw

(20 in-lbs)

Hex Head

(60 in-lbs)

Module Grounding Lug

Rail Grounding Lug

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 7

B. PLACE MODULE

Place module on rails (module cells not shown for

clarity). When installing CAMO the module can

overhang the rail no more than 1/4".

D. SECURE TO FRAME

Rotate handle with an upwards motion until CAMO

snaps into rail channel. Ensure CAMO bonding

pins are fully seated on top of module frame.

CAMO

A. SLIDE INTO RAIL

Slide CAMO into rail channel far enough to clear the

module frame. CAMO requires 6" of clearance from end of

rail.

C. PULL TOWARDS END

Pull CAMO towards rail ends, at 45 degree angle, so the

bonding bolt contacts the module ange edge.

6" Clearance

8" BONDING JUMPER

8" Bonding Jumper is an electrical bonding jumper that can

be used on the Flush Mount System for row to row bonding;

making the module frames the medium for the equipment

ground path.

➢ Bonding jumper is pushed onto the bottom ange of the module.

➢ New jumpers should be used if re-installation of jumper is required.

➢ Supports bottom ange thicknesses from 1.2mm to 3.1mm.

FRAME COMPATIBILITY

CAMO has been tested or evaluated with all modules listed in the

Module Compatibility section having frames within the referenced

dimensions. Be sure the specic module being used meets the

dimension requirements.

➢ For module manufacturer specic compatibility where applicable, please refer

to IronRidge online Design Assistant

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 8

EXPANSION JOINTS

BOSS

Insert BOSS into rst Rail up to the Alignment Circle, Slide

second Rail over BOSS to the second Alignment Circle,

leaving a 1" gap between the Rails.

There must be a 1" of space between the edge of the Rail

and the edge of the panel to allow proper installation of the

UFO and Stopper Sleeve.

A A

B B

C C

D D

E E

F F

No Modules Over Gap

One Bonding Strap Per Break In

Array

A A

B B

C C

D D

E E

F F

No Modules Over Gap

No Bonding Strap required for

BOSS

Expansion Joints are required every 100' of continuous rail to allow for thermal expansion and contraction of the system.

➢ Do not install modules over expansion joint.

➢ Expansion Joints are required every 60' of continuous rail when installing on HUG.

1" Gap Alignment

Circles

END CAPS (OPTIONAL)

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 9

ELECTRICAL DIAGRAM

UFO

Grounding Lug

Minimum 10 AWG

Copper Wire

Fault Current

Ground Path

Bonded Splice (Rail Connection)

*One Module Grounding Lug or Rail Grounding lug is required per row of a system.

** The use of the 8" Bonding Jumper eliminates the need for row to row bonding. A minimum of one grounding lug

per continuous array is required for earth ground.

CAMO

UFO or

CAMO

8" Bonding Jumper (Alternative row to row bond)**

Rail Grounding Lug*

Module Grounding Lug*

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 10

COMPOSITION SHINGLE

Locate roof rafters and mark locations on roof. Drill 1/4"

pilot holes perpendicular to the roof and back ll with

roong manufacturers' approved sealant. Slide ashing

between 1st and 2nd course of shingles, ensuring both

that the ashing reaches under the 3rd shingle course and

doesn't overhang the downhill shingle course. Line up with

pilot hole and insert supplied lag bolt with washer through

ashing. With a 7/16" Socket fully seat lag bolt. Place Cap

onto ashing in desired orientation for E/W or N/S rails and

rotate 180 degrees until it locks into place.

➢ Rail can be installed on either side of FlashFoot2 Cap.

➢ For additional details refer to the full FlashFoot2 Installation

Manual.

FLASHFOOT2

FLASHVUE

Locate rafters and snap vertical and horizontal lines to

mark locations of ashings. Drill 1/4” pilot holes, then

backll with an approved sealant. Slide ashing between

1st and 2nd course of shingles, ensuring both that the

ashing reaches under the 3rd shingle course and doesn't

overhang the downhill shingle course. Line up pilot hole

with View Port. Press Grip Cap onto ashing in desired

orientation for E/W or N/S rails. Insert Lag Bolt with

mechanically bonded washer through ashing. With a

7/16" Socket drive Lag Bolt until fully seated. FlashVue

is now installed and ready for IronRidge XR Rails.

Attach rails to either side of the open slot using bonding

hardware. Level rail at desired height, then torque to 250

in-lbs (21 ft-lbs).

When installing Gripcap+ on roofs with undulations greater

than 1 inch, install GripCap+ in low points across the array

as required.

➢ For additional details refer to the full FlashVue Installation

Manual.

➢ For additional details on the GripCap+ refer to the full GripCap+

Installation Manual.

Torque to

250 in-lbs

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 11

COMPOSITION SHINGLE

QM L-MOUNT

Locate roof rafters and mark locations on roof. Drill

7/32”(Lag) or 1/8"(ST) pilot holes perpendicular to the roof

and back ll with roong manufacturers' approved sealant.

Slide ashing between 1st and 2nd course of shingles,

ensuring both that the ashing reaches under the 3rd

shingle course and doesn't overhang the downhill shingle

course. Place L-foot on ute and rotate into desired

position. Prepare lag bolt or structural screw with sealing

washer. Use 1/2" socket to drive prepared lag bolt through

L-foot until fully seated and L-foot can no longer rotate

easily.

Torque Nut to 156 in-lbs (13 ft-lbs) for ST.

Attach

rail to L-Foot with Bonding Hardware and torque to 250

in-lbs (21 ft-lbs).

➢ Structural screw can be driven with T-30 hex head bit.

➢ For additional details refer to the full QM Installation Manual.

QM QBASE COMPOSITION MOUNT

Locate roof rafters and mark locations on roof. Align

QBase vertical holes over center rafter and mark. Drill two

pilot holes with 7/32" drill bit, perpendicular to roof and

back ll with roong manufacturers' approved sealant.

Set grade 8 cap screw through bottom of QBase, place

QBase over drilled holes and secure lags. Screw Post to

QBase. Proceed with roong up until the ashing should

be installed. Install ashing over mount. Allow roong to

proceed to the next course. Apply sealant where post and

ashing meet, install EPDM counter ashing collar. Attach

L-Foot on Stando with hardware. Torque to 174 in-lbs

(14.5 ft-lbs). Attach rail to L-Foot with Bonding Hardware

and torque to 250 in-lbs (21 ft-lbs).

➢ For additional details refer to the full QM Installation Manual.

Torque to

174 in-lbs

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 12

COMPOSITION SHINGLE

Conrm shingle step does not exceed 1/8”. Locate and

mark centers of rafters to be mounted. Select the courses of

shingles where mounts will be placed. Peel o release liner.

Align HUG horizontally using the shingle edge or chalk line

with the alignment grooves on the mount. Once in desired

location, lightly press against roof to preliminarily hold the

mount in place. Drive RD Structural Screw using 5/16”

socket, ensuring that two screws are correctly installed into

the center of the rafter. Drive screws until fully seated.

➢ Rail can be installed on either side of HUG.

➢ For complete installation requirements and limitations, please

refer to the HUG Installation Manual.

➢ HUG is only approved for installation with IronRidge RD

Structural Screws.

➢ HUG cannot be installed between courses.

HUG (RAFTER)

Conrm shingle step does not exceed 1/8”. Locate and mark

attachment loactions. Select the courses of shingles where

mounts will be placed. Peel o release liner. Align HUG

horizontally using the shingle edge or chalk line with the

alignment grooves on the mount. Once in desired location,

lightly press against roof to preliminarily hold the mount in

place. Drive screws using 5/16” socket, until fully seated.

All 6 RD Structural Screws must be used in deck mounted

conditions.

➢ Rail can be installed on either side of HUG.

➢ For complete installation requirements and limitations, please

refer to the HUG Installation Manual.

➢ HUG is only approved for installation with IronRidge RD

Structural Screws.

➢ Rows of rail exceeding 60 feet require a thermal expansion joint

when using HUG.

HUG (DECK)

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 13

TILE

Orient Base to desired position

Tighten until fully seated

Torque to

250 in-lbs

QM TILE REPLACEMENT

Remove tile and mark rafter. Measure up 8 3/4" from the

adjacent tiles and mark horizontal across rafter. Align

baseplate over rafter so that the lag holes align with the

post groove. The orientation of the plate can be adjusted

cross roof, mark location of lag holes on the roof. Drill two

1/8" Pilot holes and back ll with roong manufacturers'

approved sealant. Waterproof at underlayment level

according to roong manufacturers' instructions and the

Tile Roong Industry Alliance guidelines. Use T-30 Torx

bit to lag base into position. Insert Grade 8 Serrated

Flange Bolt into bottom of the Post, slide Post into

Base channel. Line up post with the hole in the Tile

Replacement Flashing. Leave loose for adjustments.

Place Tile Replacement Flashing over the Post and Mount,

allowing the ashing to properly interlock with surrounding

tiles. Secure Post by tightening with channel lock pliers.

Replace all tiles. Apply a bead of sealant where the post

meets the ashing, slip EPDM collar over post and down to

ashing. Attach L-Foot on Stando with hardware. Torque

to 174 in-lbs (14.5 ft-lbs). Attach rail to L-Foot with

Bonding Hardware and torque to 250 in-lbs (21 ft-lbs).

➢ If deck level ashing is required, approved ashing methods

include user supplied adhesive backed exible ashing.

➢ For additional details refer to the full QM Installation Manual.

Remove tile and mark rafter. Use base as guide to

drill 1/4” pilot hole and ll with roong manufacturer’s

approved sealant. Install optional Roof Flashing and seal

appropriately. Insert lag bolt with bonded washer through

base (and ashing if used) and drive until fully seated.

Insert Tile Replacement Flashing, lower onto base and

apply pressure over the threaded post until it dimples the

ashing. Place L-Foot over dimple and tap with hammer to

punch threaded post through the ashing. Ensure punched

pieces of ashing are cleared away. Form ashing as

needed to sit ush with surrounding tiles, position L-Foot in

desired orientation and torque hardware to 132 in-lbs (11

ft-lbs). Attach rail to L-Foot with Aire Dock and torque to

250 in-lbs (21 ft-lbs).

➢ Base can be installed in any orientation relative to rafter.

➢ Ensure L-Foot does not extend above rail.

➢ Optional deck level ashing is available. Standalone installation

manual available on website

➢ Standalone Knockout Tile manual available on website.

Rafter

Dimple

Tap With

Hammer

Torque to

132 in-lbs

KNOCKOUT TILE

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 14

TILE

Remove tile and mark rafter, use Base Plate to mark two

holes on rafter. Drill two 7/32" pilot holes and back ll

with roong manufacturers' approved sealant. Use 1/2"

socket to drive lag into place. Slide hook into place and

adjust to desired position. Drive self-tapping screw using

a #3 Phillips bit to lock hook in place. Clean underlayment

and apply a bead of sealant compatible with roong

manufacturer, install ashing over mount. Fasten sub-

ashing to deck with one roong nail in each corner.

Waterproof at underlayment level according to roong

manufacturers' instructions and the Tile Roong Industry

Alliance guidelines. Cut clearance notch in the weather

guard of tile as needed or utilize QM Tile Replacement

Flashings. Attach rails to either side of slot using Bonding

Hardware and torque to 250 in-lbs (21-ft-lbs).

➢ Position arm near the center of valley for curved tiles.

➢ Position arm away from seam of joining at tiles.

➢ Ensure top of hook does not extend above rail.

➢ For additional details refer to the full QM Installation Manual.

QM QUICK HOOK

Remove tile and mark rafter. Position base over rafter,

adjust arm if necessary and torque hardware to 132 in-lbs

(11 ft-lbs). Use base as guide to drill 1/4" pilot holes, back

ll with roong manufacturer’s approved sealant, then

insert lag bolts and tighten until fully seated. Replace tiles

and notch as necessary to ensure proper t. Attach rails to

either side of slot using Bonding Hardware and torque to

250 in-lbs (21-ft-lbs).

➢ Position arm near the center of valley for curved tiles.

➢ Position arm away from seam of joining at tiles.

➢ Ensure top of hook does not extend above rail.

➢ Standalone All Tile Hook manual available on website.

Rafter

Torque to

132 in-lbs

Torque to

250 in-lbs

Tighten Until

Fully Seated

ALL TILE HOOK

Torque to

250 in-lbs

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 15

TILE

ADDITIONAL ROOF TYPES

QM QBASE METAL, SHAKE AND SLATE

The QM QBase can be used to install on multiple roong

types with dierent installation methods.

➢ For instructions on installing the QBase on Slate refer to the full

QM Installation Manual.

➢ For instructions on installing the QBase on Shake refer to the full

QM Installation Manual.

➢ For instructions on installing the QBase on Metal Shingle refer to

the full QM Installation Manual.

Remove tile and mark rafter. Measure up 6 5/8" from

bottom of tiles and mark horizontally. Align QBase over

rafter center and drill two 7/32" pilot holes, back ll with

roong manufacturers' approved sealant. Place grade-8

Cap Screw under QBase, lag QBase into rafter location.

Install Sub-ashing, waterproof at underlayment level

according to roong manufacturers' instructions and the

Tile Roong Industry Alliance guidelines. Cut tile with

diamond blade to allow post to pass through. Place tile

in position and then install Post. Install 18"x18" ashing,

pre-bent to follow the contour of the tile as required. Apply

sealant where Post and Flashing meet and install EPDM

counter ashing. Attach L-Foot on Stando with hardware.

Torque to 174 in-lbs (14.5 ft-lbs). Attach rails to L-Foot

using Bonding Hardware and torque to 250 in-lbs (21-ft-

lbs).

➢ For additional details refer to the full QM Installation Manual.

QM QBASE UNIVERSAL TILE MOUNT

Torque to

174 in-lbs

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 16

LOW SLOPE ROOFS

Flat Roof Attachment can be used with an L-foot for ush

mounting modules on low sloped roofs. Mark locations

for Flat Roof Attachment. Screws should be installed

symmetrically to each other. If using a membrane ashing,

remove the silicone washer's protective liner prior to

attaching the membrane. Attach L-foot with washers and

3/8” hardware torqued to 250 in-lbs (21 ft-lbs). Seal

attachment and/or membrane per roong manufacturer’s

requirements.

➢ Type, size, and quantity of roof screws to be specied by

Structural Engineer. Fastener size not to exceed #15.

➢ Membrane ashing available for TPO, PVC, and KEE roofs.

Ensure membrane ashing is compatible with existing roong

material.

➢ If membrane ashing is not used, only washer on top of L-Foot is

required.

➢ Standalone Flat Roof Attachment Manual available on website.

250 in-lbs

Flat Roof

Attachment

Hardware

L-Foot

Flat Roof

Attachment

Membrane

Flashing

FLAT ROOF ATTACHMENT

Locate the desired mount placement over a rafter. Using

the base as a template, mark the two penetration

points. Drill two 7/32" pilot holes, back ll with roong

manufacturers' approved sealant. Place the grade-8 hex

bolt in the bottom of the base and screw the Post. Attach

L-Foot on Stando with hardware. Torque to 174 in-lbs

(14.5 ft-lbs). Attach rail to L-Foot with Bonding Hardware

and torque to 250 in-lbs (21 ft-lbs).

The mount can be ashed with available 9", 12" or

18" aluminum ashings, pitch pocket or curb, or with a

membrane cone ashing. If using a membrane ashing

utilize the services of a qualied roofer

➢ For additional details refer to the full QM Installation Manual.

QM QBASE MOUNT

Screws provided by

others. Shown for

refrence

Torque to

174 in-lbs

METAL ROOF

Locate the desired mount placement over a roong seam,

make sure block is fully seated on metal seam. Torque

Set Screws to 150 in-lbs(12.5 ft-lbs) using 3/16" Hex

Drive, alternate driving each bolt till required torque is met.

Slide Hex Bolt into slot and to desired position. Place rail

attachment bracket over Hex Bolt and secure with Flange

Nut, torque Flange Nut to 150 in-lbs(12.5 ft-lbs) using

1/2" socket.

➢ For additional details refer to the full QM Installation Manual.

➢ Certication of Lynx calmp includes bonding to both painted and

galvalume metal roofs.

➢ The technology in this product is licensed by S-5!

QM LYNX

Slide hardware in to

desired position

Torque to

150 in-lbs

END CAPS (OPTIONAL)

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 17

CONDUIT PENETRATION FLASHINGS

QM CONDUIT PENETRATION FLASHING - COMP SHINGLE

Mark a drill point so that the ashing reaches up to the 3rd

shingle course. Drill your conduit hole next to the rafter

so you can secure the conduit below the roof surface.

Cut shingle and remove nails as needed to center the

drilled hole and ashing hole. Apply roong manufacturer's

approved sealant on the underside of the ashing in a

Upside down U and to top of ashing. Under the 3rd

course and through the second course secure ashing

with 2 roong nails, apply sealant over the nail heads. Cut

EPDM collar to appropriate size. Apply a bead of sealant

compatible with the roong manufacturer and EPDM

rubber to anywhere the EPDM collar contacts.

➢ Be sure to secure conduit to rafters below the roof surface per

local building codes and NEC code requirements.

➢ Cut EPDM collar to appropriate size using the sizing chart in the

installation manual, approved for 1/2" to 1" EMT.

➢ For additional details refer to the full QM Installation Manual.

Nails under the third

course

Rafter

Drill your conduit hole next to the rafter so that you can

secure the conduit below the roof surface. Apply roong

manufacturer approve sealant to the underside of the

sub-ashing in the shape of an upside down U. Clear away

any dust and debris to install sub-ashing. Waterproof at

under laminate level according to roong manufacturer

instructions and Tile Roong Institute Guidelines. Under

the top layer of felt, secure the sub-ashing with two

roong nails. Cut EPDM collar to appropriate size. Apply a

bead of sealant compatible with the roong manufacturer

and EPDM rubber to anywhere the EPDM collar contacts.

With a diamond blade cut tile to allow conduit to pass

through, replace all tiles. Bend the ashing to follow the

contour of the tiles. Place ashing over the conduit and

tuck up under the next course of tiles. Apply a bead of

sealant compatible with the roong manufacturer and

EPDM rubber to anywhere the EPDM collar contacts.

Slide collar onto conduit all the way down to the ashing.

➢ Be sure to secure conduit to rafters below the roof surface per

local building codes and NEC code requirements.

➢ Cut EPDM collar to appropriate size using the sizing chart in the

installation manual, approved for 1/2" to 1" EMT.

➢ For additional details refer to the full QM Installation Manual.

Rafter

QM CONDUIT PENETRATION FLASHING - TILE

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 18

CONDUIT MOUNT

Remove the tile that the mount will be installed on, and the

tiles in the course above it. Lift the bottom of the tile and

slide the bottom clamp over the bottom edge of the tile.

Insert the 4" tap bolt through the slot into the threaded hole

and use a 7/16" socket to thread the screw. Tighten until

the top clamp hook end unbends and forms a 90 degree

angle with the tile. Use the Cap Screw (included) to attach

your pipe clamp (not included) to bottom clamp. Insert

conduit and tighten with 7/16" socket.

➢ The clamp is reversible, use the wider hook end on tile greater

than 1" thick and the thinner hook end on tiles less than 1" thick.

➢ The installation process is the same on curved tile, make sure

that the Conduit Mount is installed on the crown(high point) of the

tile.

➢ Install mounts as required to support conduit across the roof.

➢ For additional details refer to the full QM Installation Manual.

QM CONDUIT MOUNT - TILE

Place conduit mounts along path of conduit. Lift shingle

above mount location and insert ashing into position.

Mark center for drilling, remove ashing and drill pilot

hole with 1/8" bit. Clean area, ll hole with roong

manufacturer's approved sealant. Lift shingle and slide

Conduit Mount into place. Prepare the lag bolt with sealing

washer and pipe clamp (not included). Insert lag through

hole in block and drill with 7/16" socket until block is tight.

➢ Install mounts as required to support conduit across the roof.

➢ For additional details refer to the full QM Installation Manual.

QM CONDUIT MOUNT - COMPOSITION SHINGLE

End Caps add a completed look and keep debris and

pests from collecting inside rail.

Firmly press End Cap onto rail end.

➢ End Caps come in sets of left and right. Check that the proper

amount of each has been provided.

END CAPS

QM BUG - COMPOSITION SHINGLE

Place BUG conduit mounts along path of conduit. Clean

area, place mount and drive RD Structural Screw using

5/16” socket. Prepare the Tri-lobe Screw and pipe clamp

(not included). Insert screw in an unused hole in block and

drill with 5/16" socket until screw is tight.

➢ Install mounts as required to support conduit across the roof.

➢ For additional details refer to the full QM Installation Manual.

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 19

END CAPSWIRE CLIPS

Wire Clips oer a simple wire management solution.

Firmly press Wire Clip into top rail slot. Run electrical wire

through open clip. Snap closed once all wires have been

placed.

➢ Wire Clip ts up to quantity 10 - 10 AWG PV Wire or

equivalent bundled diameter.

Press Clip

into Slot

Run Wire

Snap Clip

Closed

JAYBOX

Prior to installation, use step drill bit to place pass through

holes for conduits or water-tight connectors. Drill bit

starter locations are provided on the sides and front of

enclosure.

➢ Do not install conduit facing up roof.

B (Rail).

Use rail-specic MLPE mounting hardware to attach Rail

Hangers to rail. Ensure junction box is pushed as close

to the rail as possible. Torque to 80-in lbs (1/2" or 7/16"

socket).

➢ Do not overtighten

➢ If installing in areas with ground snow loads greater than

40 psf, install JayBox under module directly next to module

frame edge.

B (Shingle).

Align sealing oval of box to align with mating feature on

ashing. An EPDM foam gasket is pre-installed to the

underside of the junction box to seal the ashing to the

box without the need for additional sealant. Secure with

supplied #12 x 1-¾" deck screws (2x) until the junction

box is pulled tight to the ashing. Do not over-tighten

screws to avoid stripping screws in OSB.

➢ If installing pass through ttings, ensure that the JayBox and

roof deck are both properly prepared. Complete installation

process before attaching the Jaybox to the deck.

➢ Do not install JayBox under shingle seam as illustrated below.

Install wiring, conduit and ttings per NEC

requirements and following local AHJ guidance.

Using Philips Head Driver tighten the bolt.

➢ For additional details refer to the full QM Installation Manual.

Keyways and

shingle joints

Drill starter

locations

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 20

MICROINVERTER KITS

One Microinverter

Kit Required

(80 in-lbs)

Use IronRidge's Microinverter Kit to bond compatible

microinverters and power optimizers to the racking system.

Insert Microinverter Kit T-bolt into top rail slot. Place

compatible microinverter or power optimizer into position

and tighten hex nut to 80 in-lbs.

➢ MLPE devices shall be installed near modules frames whenever

possible.

On AP Systems and Yotta

equipment, remove Grounding

Washer

Two Microinverter

Kits Required

(80 in-lbs)

➢ Remove Grounding Washer on AP Systems QS1, QT2, DS3 and YC600

and Yotta inverters before installing to XR rails.

➢ Remove the Stainless Steel Clip on Tigo-”A” MLPE Devices before

attaching to XR rails.

➢ Use the number of IronRidge Microinverter kits allowed by the MLPE

mounting ange. Some will require 1 kit and others 2 kits.

AP Systems DS3, QS1, QT2 and YC600

Darfon MIG240, MIG300, G320, G640

Duracell D350-M1, D700-M2, D1500-M4

Enphase M250-72, 250-60, M215-60, C250-72, S230, S280,

IQ 6, IQ 6+, IQ7, IQ 7A, IQ 7+, IQ7 PD, IQ 7X, Q

Aggregator; IQ8-60, IQ8PLUS-72, IQ8A-72, IQ8H-

208-72, IQ8H-240-72, IQ8M-72, may be followed

by -2-US; IQ8H-3P-72-E-US or IQ8P-3P-72-E-US

Generac S2502

Hoymiles HMA-xxxYY-ZZ

where "A" can be blank or S, xxx can be 300,

350, 400, 450, 500, 600, 700, 800, 900, 1000, 1200,

1500, 1600, 1800 or 2000; "YY" can be NT, 1T, 2T,

4T; and "ZZ" can be blank, NA or 208-NA

NEP

Microinverters

BDM-xxx-yyy

Where "xxx" can be 300, 300X2, 350, 400, 500,

550, 650, 800, 1000; and "yyy" can be blank, 208A

or 240A

NEP Rapid

Shutdown

PVG-1, PVG-2, PVG-3, PVG-4

SMA RoofCommKit-P2-US, TS4-R Module Retrot Kits

(TS4-R-S,

TS4-R-O, TS4-R-F)

Solar Edge M1600, P300, P320, P340, P370, P400, P401,

P405, P485, P505, P600, P700, P730, P750,

P800p, P800s, P801, P850, P860, P950, P960,

P1100, P1101, S440, S500, S500B, S650B, S1200,

S1201

Tigo Tigo Access Point (TAP)

TS4-R-X (where X can be F, M, O, or S)

TS4-R-X-DUO (where X can be M, O, or S)

TS4-A-X (where X can be F, 2F, O, O-DUO, or S)

Yotta DPI 208/480

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 21

Use IronRidge's Microinverter Kit to bond compatible microstroage

devices to the racking system. Insert Microinverter Kit T-bolt into top

rail slot. Place compatible microstorage into position and tighten hex

nut to 80 in-lbs.

Microinverter Kit

(80 in-lbs)

SYSTEMS USING MICROSTORAGE PRODUCTS

COMPATIBLE PRODUCTS

PHAZR

PHAZR Devices PHAZR-X, where X is 6-12.

Solpad

Solpad Inverter model SI-1k

Solpad Battery Storage model SB-2K

Solpad Junction Box model SJB-4k

➢ Running a separate equipment grounding conductor to the PHAZR or

Solpad devices is not required.

➢ If installing in areas with ground snow loads greater than 40 psf and

underneath a module, install PHAZR and Solpad devices as close as

possible to module frame edge.

➢ Solpad may only be installed on XR-100 and XR-1000

➢ Solpad may only be installed with modules having a frame thickness of

35mm or greater.

➢ Use the number of IronRidge Microinverter kits allowed by the microstorage

mounting ange. Some will require 1 kit and others 2 kits.

Insert Frameless Kit T-bolt in top rail slot. Place star

washer over T-bolt, allowing it to rest on top of rail.

Secure module clamps with a hex nut and torque to 80

in-lbs.

Place

Star Washer

Module Clamp

(80 in-lbs)

Grounding Lugs

Required on Every Rail

FRAMELESS MODULE KITS

COMPATIBLE PRODUCTS

Sunforson

Sunforson silver or black SFS-UTMC-200(B) mid and SFS-UTEC-

200(B) end clamps.

Sunpreme

Sunpreme silver or black mid and end clamps with part numbers

7500105X where "X" is 1, 5, 6 or 7.

Ironridge

IronRidge silver or black mid and end clamps with part numbers

FMLS-XC-001-Y where "X" is E or M and "Y" is B or blank.

➢ Follow module manufacturer's installation instructions to install

the module clamps.

➢ Frameless modules require using a Grounding Lug on every rail.

➢ For Sunpreme Modules Only: If required to use slide prevention

hardware, see Module Slide Prevention Addendum (Version

1.10).

Two sets of two

Microinverter Kits

(80 in-lbs)

Solpad

PHAZR

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 22

CONTOUR

Install Contour

Install Contour on a completed array.

A. Start by placing Contour Clamp on module frame within

12 inches of the down roof corner of the array. Each piece

of 84" Contour Trim must be suppported by two Clamps.

Clamps must be installed in the 12" clamping zones at

edge of trim. Once trim is placed and in position, secure

trim by tightening Clamp set screw to 80 in-lbs.

B. Multiple Contour pieces can be joined using Contour

Splice. Install Splice on exsisting Contour edge and install

Clamps in appropriate clamping zones for next piece of

trim. Place trim on Clamps, slide into splice to join two

pieces together. Secure Contour by tightening Clamp set

screw to 80 in-lbs. Repeat as needed across the array.

C. Cut trim to line up with edge of array.

D. Install Clamps within clamping zones on side of array.

Install second Clamp as needed up array. Place Corner

Cap on trim and slide side trim to align with Cap. Repeat

as needed along roof for both inside and outside corners.

E. Use optional End Caps to cover any exposed edges of

Contour as desired.

➢ Do not install on side of array facing roof peak.

➢ Contour can be installed with 1 clamp if trim section is 12" long

(or shorter) and has a splice attached on one end, on which the

section of trim the 12" section is spliced to also has 2 clamps.

➢ Contour Trim when installed when installed up roof requires the

use of Aire Stealth Clamps.

➢ Wind Speed: no restrictions

➢ Ground Snow: up to 90 PSF

12.00 12.00

Clamping Zones

D.C.

Push Trim and

install ush

FRAME COMPATIBILITY

Contour Clamp has been tested or evaluated with all

modules having frames within the referenced dimensions.

Be sure the specic module being used meets the

dimension requirements.

➢ Flange Thickness: 1-3.5mm

➢ Usable Flange Length: 0-33mm.

Frame Compatibility:

X = 1-3.5mm

Y = 0-33mm

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 23

MODULE COMPATIBILITY

MAKE MODELS

The Flush Mount System has been tested and evaluated to UL 2703 for bonding, grounding, mechanical loading and re

classication, and may be used to ground and/or mount PV modules listed to UL 1703 or UL 61730. A list of approved

modules is included below. Unless otherwise noted, “xxx” refers to the module power rating and both black and silver

frames are included in the certication.

FRAMED MODULE LIST

Adani

Adani modules with 30, 35 and 40 mm frames

ASX-Y-ZZ-xxx

Where "X" can be B, M or P, "Y" can be 6, 7 or M10 and "ZZ" can be blank, 144, PERC, B-PERC, or AB-

PERC

AIONRISE

AIONRISE modules with 35 and 40 mm frames

AIONyyG1-xxx

Where "yy" can be 60 or 72

Amerisolar

Amerisolar modules with 35 and 40 mm frames

AS-bYxxxZ

Where "b" can be 5 or 6; "Y" can be M, P, M27, P27, M30, or P30; and "Z" can be blank, W or WB

Aptos Solar

Aptos modules with 35 and 40 mm frames

DNA-yy-zzaa-xxxbb

Where "yy" can be 108, 120 or 144; "zz" can be MF or BF; "aa" can be 10, 23 or 26; and "bb" can be blank

or W-DG

Astronergy Solar

Astronergy modules with 30, 35 and 40 mm frames

aaSMbbyyC/zz-xxx

Where “aa” can be CH or A; "bb" can be 60, 66, or 72; “yy” can be blank, 10 or 12; "C" can M, P, M(BL),

M-HC, M(BL)-HC, P-HC, M(DG), M(DGT) or N(DG); and “zz” can be blank, HV, F-B, or F-BH

ASUN

ASUN modules with 35 and 40 mm frames

ASUN-xxx-YYZZ-aa

Where "YY" can be 60 or 72; "ZZ" can be M,or MH5; and "aa" can be blank or BB

Auxin

Auxin modules with 35 and 40 mm frames

AXNCyzAxxxB

Where "C" can be 6, 10 or G1; "y" can be M or P; "z" can be blank, 08, 09, 610, 11, or 612; and "A" can be

blank, F, M or T; and "B" can be blank, A, B, C or W

Axitec

Axitec Modules with 30, 35 and 40 mm frames

AC-xxxY/aaZZb

Where "Y" can be M, P, MB, MBT or MH; "aa" can be blank, 125- or 156-; "ZZ" can be 54, 60, 72, 108, 120,

or 144; "b" can be S, X, V, VB, XV, or MX

Bluesun Solar

Bluesun modules with 30 and 35 mm frames

BSMxxxY-AAA

Where "Y" can be M or M10; and "AAA" can be 54HPH, 60HPH or 72HBD

Boviet

Boviet modules with 35 and 40 mm frames

BVMZZaaYY-xxxBcc

Where "ZZ" can be 66 or 76; "aa" can be 9, 10 or 12; "YY" is M or P; and "B" can be blank, L or S; and "cc"

can be blank, H, H-BF, H-BF-DG, H-HC, H-HC-BF, H-HC-BF-DG, HC-BF or HC-BF-DG

BYD

BYD modules with 35 mm frames

BYDxxxAY-ZZ

Where "A" can be M6, P6, MH, MLT or PH; "Y" can be C or K; and "ZZ" can be 30 or 36

Canadian Solar

Canadian Solar modules with 30, 32, 35 and 40 mm frames

CSbY-xxxZ

Where "b" can be 1, 3, 6, 6.1 or 7; "Y" can be H, K, L, N, P, R, U, V, W, X, Y, -54TM or -72TB; and "Z" can be

H, M, P, MS, PX , M-SD, P-AG, P-SD, MB-AG, PB-AG, MS-AG, MS-HL or MS-SD

CertainTeed

CertainTeed modules with 30, 35 and 40 mm frames

CTBBxxxYZZ-AA

Where "BB" can be blank or M10; "Y" can be M, P, or HC; "ZZ" can be 00, 01, 10, or 11; and "AA" can be 01,

02, 03, 04, 06, 08 or 09

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 24

MODULE COMPATIBILITY

Crossroads Solar

Crossroads Solar modules with 40 mm frames

Crossroads Solar xxx

CSUN

Csun modules with 35 and 40 mm frames

YYxxx-zzAbb

Where "YY" is CSUN or SST; "zz" is blank, 60, or 72; and "A" is blank, P, M or MM; "bb" is blank, BB, 5BB,

BW, or ROOF

Dehui

Dehui modules with 30, 35 and 40 mm frames

DH-MYYYZ-xxx

Where “YYY” can be 760, 772, 860, 872; and “Z” can be B, F or W

Ecosolargy

Ecosolargy modules with 35 and 40 mm frames

ECOxxxYzzA-bbD

Where “Y” can be A, H, S, or T; “zz” can be 125 or 156; “A” can be M or P; “bb” can be 60 or 72; and “D” can

be blank or B

Emmvee

Emmvee modules with 35 mm frames

Exxx-YYZZZ-A

Where "YY" can be M, P, HCM, HCMW, HCBG, HCBT; "ZZZ" can be 72, 120 or 144; and "A" can be blank or

ET Solar

(EliTe Solar)

ET Solar modules with 30, 35 and 40 mm frames

ET-YZZZxxxAA

Where "Y" can be P, L, M or N; "ZZZ" can be 660, 660BH, 672, 672BH, 754BH, 760BH, 766BH, 772BH,

760TBH, 766TBH or 772TBH; and "AA" can be GL, TB, TW, WB, WW, BB, WBG, WWG, WBAC, WBCO,

WWCO, WWBCO or BBAC

Flex

Flex modules with 35 and 40 mm frames

FXS-xxxYY-ZZ;

Where “YY” can be BB or BC; and “ZZ” can be MAA1B, MAA1W, MAB1W, SAA1B, SAA1W, SAC1B,

SAC1W, SAD1W, SBA1B, SBA1W, SBC1B, or SBC1W

Freedom Forever

Freedom Forever modules with 35 mm frames

FF-MPa-BBB-xxx

Where "a" can be blank or 1

Freevolt

Freevolt modules with 35 mm frames

ECP-PVGRAF-144HC-xxx

GCL

GCL modules with 35 mm and 40 mm frames

GCL-ab/YY xxx

Where “a” can be M or P; “b” can be 3 or 6; and “YY” can be 60, 72, 72H, or 72DH

GigaWatt Solar

Gigawatt modules with 40 mm frames

GWxxxYY

Where “YY” can be either PB or MB

Goldi

Goldi modules with 35 mm frames

GS10-Byyy-zz-xxx

Where "yyy" can be 108 or 144; and "zz" can be GF or TF

Grape Solar

Grape modules with 35 mm frames

GS-M120-xxx-FAB1

GreenWatts Solar

GreenWatts modules with 30 and 35mm frames

HSYY-A-xxx-ZZ

Where "YY" can be 54, 60, 66, 72 or 78; "A" can be blank or F; and "ZZ" can be MN or BOB

Hansol

Hansol modules with 35 and 40 mm frames

HSxxxYY-zz

Where “YY” can be PB, PD, PE, TB, TD, UB, UD, or UE; and “zz” can be AH2, AN1, AN3, AN4, HH2, HV1,

or JH2

Hanwa Solar

Hanwha Solar modules with 40 mm frames

HSLaaP6-YY-1-xxxZ

Where “aa” can be either 60 or 72; “YY” can be PA or PB; and “Z” can be blank or B

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 25

MODULE COMPATIBILITY

Hanwha Q CELLS

Hanwha Q CELLS Modules with 30, 32, 35, 40 mm frames

aaYY-ZZ-xxx

where "aa" can be Q. or B.; "YY" can be PLUS, PRO, PEAK, LINE PRO, LINE PLUS, PLUS DUO, PEAK

DUO or TRON; and "ZZ" can be G3, G3.1, G4, G4.1, L-G2, L-G2.3, L-G3, L-G3.1, L-G3y, L-G4, L-G4.2,

L-G4y, LG4.2/TAA, BFR-G3, BLK-G3, BFR-G3.1, BLK-G3.1, BFR-G4, BFR-G4.1, BFR G4.3, BLK-G4.1,

G4/SC, G4.1/SC, G4.1/TAA, G4.1/MAX, BFR G4.1/TAA, BFR G4.1/MAX, BLK G4.1/TAA, BLK G4.1/SC,

EC-G4.4, G5, G5/SC, G5/TS, BLK-G5, BLK-G5/SC, BLK-G5/TS, L-G5, L-G5.1, L-G5.2, L-G5.2/H, L-G5.3,

G6, G6/SC, G6/TS, G6+/TS, G6+, BLK-G6, L-G6, L-G6.1, L-G6.2, L-G6.3, G7, BLK-G6+, BLK-G6+/AC,

BLK-G6+/HL, BLK-G6+/SC, BLK-G6/TS, BLK-G6+/TS, BLK-G7, G7.2, G8, BLK-G8, G8+, BLK-G8+ L-G7,

L-G7.1, L-G7.2, L-G7.3, L-G8, L-G8.1, L-G8.2, L-G8.3, L-G8.3/BFF, L-G8.3/BFG, L-G8.3/BGT, M-G2+, BLK

M-G2+, ML-G9, BLK ML-G9, ML-G9+, BLK ML-G9+, BLK-G10, BLK-G10+, BLK G10+/AC, BLK-G10+/HL,

ML-G10, BLK ML-G10, ML-G10+, BLK ML-G10+, ML-G10.a, BLK ML-G10.a, ML-G10.a+, BLK ML-G10.

a+, BLK ML-G10 +/t, BLK ML-G10+/TS, XL-G2.3/BFG, XL-G9, XL-G9.2, XL-G9.3, XL-G9.3/BFG, XL-G10.2,

XL-G10.3, XL-G10.c, XL-G10.d, XL-G10.d/BFG, XL-G10.3/BFG, XL-G11.2, XL-G11.3, XL-G11.3/BFG or

XL-G11S.3/BFG

Heliene

Heliene modules with 35 and 40 mm frames

YYZZxxxA

Where "YY" can be 36, 60, 72, 96, 108, 120, 132, 144 or 156; "ZZ" can be HC, M, P, or MBLK; and "A" can

be blank, HomePV, Bifacial, M10-SL, M10-SL-BLK, M10 TPC SL, M10 Bifacial, M10 SL-Bifacial or M10 TPC

SL Bifacial

HT-SAAE

HT-SAAE modules with 35 and 40 mm frames

HTyy-aaaZ-xxx

Where "yy" can be 60, 66, 72 or 78, "aaa" can be 18, 156 or 166, "Z" can be M, P, M-C, P-C, M(S), M(VS),

M(V), P(V), M(V)-C, P(V)-C, or X

Hyperion Solar

(Runergy)

Hyperion modules with 30 and 35 mm frames

HY-DHzzzA8-xxxB

Where "zzz" can be 108 or 144; "A" can be N or P; and "B" can be blank or B

Hyundai

Hyundai modules with 32, 33, 35 and 40 mm frames

HiY-SxxxZZ

Where "Y" can be A, D or S; "S" can be M or S; and "ZZ" can be GI, HG, HI, KI, MI, MF, MG, OJ, PI, RI, RG,

RG(BF), RG(BK), SG, TI, TG, YH(BK) or XG(BK)

Itek

Itek Modules with 40 mm frames

IT-xxx-YY

Where “YY” can be blank, HE, or SE, or SE72

JA Solar

JA Solar modules with 30, 35 and 40 mm frames

JAyyzz-bbww-xxx/aa

Where “yy” can be M, P, M6 or P6; “zz” can be blank, (K), (L), (R), (V), (BK), (FA), (TG), (FA)(R), (L)(BK), (L)

(TG), (R)(BK), (R)(TG), (V)(BK), (BK)(TG), or (L)(BK)(TG); “bb” can be 48, 54, 60, 66, 72 or 78; "ww" can be

D09, D10, D20, D30, S01, S02, S03, S06, S09, S10, S12, S17, S20, S30 or S31; and “aa” can be BP, MB,

MR, SI, SC, PR, 3BB, 4BB, 4BB/RE, 5BB

Jakson Solar

Jakson Solar modules with 35mm frames

JH-xxxYY

Where "YY" can be BB or BT

Jinko

Jinko modules with 30, 35 and 40 mm frames

JKMYxxxZZ-aa

Where "Y" can either be blank or S; "ZZ" can be M, N, P, or PP; and "aa" can be blank, 54HL4-B, 60,

60B, 60H, 60L, 60BL, 60HL, 60HB, 60HBL, 6HBL-EP, 60-J4, 60B-J4, 60B-EP, 60(Plus), 60-V, 60-MX,

6RL3, 6RL3-B, 6TL3-B, 7RL3-V, 7RL3-TV, 72, 72B, 72-J4, 72B-J4, 72(Plus), 72-V, 72H-V, 72L-V, 72HL-V,

72HBL-V, 72HL4-V, 72HL4-BDV, 72HL4-TV, 72-MX, 72H-BDVP, 72HL-TV, or 72HL-V-MX3

KB Solar

KB Solar modules with 35 mm frames

KBS-xxx-Mono-YY

Where "YY" can be blank or BF

Kyocera

Kyocera Modules

KYxxxZZ-AA

Where “Y” can be D or U; “ZZ” can be blank, GX, or SX; and “AA” can be LPU, LFU, UPU, LPS, LPB, LFB,

LFBS, LFB2, LPB2, 3AC, 3BC, 3FC, 4AC, 4BC, 4FC, 4UC, 5AC, 5BC, 5FC, 5UC, 6BC, 6FC, 8BC, 6MCA, or

6MPA

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 26

MODULE COMPATIBILITY

LA Solar

LA Solar modules with 35 mm frames

LSxxxYY

Where "YY" can be BF, BL, BLA, HC or ST

LG modules with 35 and 40 mm frames

LGxxxYaZ-bb

Where "Y" can be A, E, M, N, Q, S; "a" can be A, 1, 2 or 3 "Z" can be C, K, T, or W; and "bb" can be A3, A5,

A6, B3, B6, E6, E6.AW5, G3, G4, J5, K4, L5, N5, V5, V6

Longi

Longi modules with 30, 35 and 40 mm frames

LRa-YYZZ-xxxM

Where "a" can be 4, 5, 6 or 7; "YY" can be blank, 54, 60, 66, or 72; and "ZZ" can be blank, BK, BP, HV, PB,

PE, PH, HBD, HGD, HIB, HIH, HPB, HPH, HIBD, HABB or HABD

Maxeon

Maxeon modules with 35, 40 and 46 mm frames

SPR-AAAY-xxx-zzz

Where "AAA" can be MAX, P or X; "Y" can be 3, 5, 6, 21 or 22; and "zzz" can be R, BLK, BLK-R, COM or

UPP

Meyer Burger

Meyer Burger Modules with 35 mm frames

Meyer Burger Black, White or Glass

Mission Solar

(mSolar)

Mission Solar modules with 30, 33, 35 and 40 mm frames

YYYbb-xxxZZaa

Where "YYY" can be MSI, MSE, TXI or TXS; "bb" can be blank, 6, 10 or 60A; "ZZ" can be blank, HN, HT,

MM, SE, SO, SQ , SR, SX, TS, 108, 120 or 144; and "aa" can be blank, 0B, 2B, BB, BW, 1J, 4G, 4J, 4S, 5K,

5R, 5T, 60, 6J, 6S, 6W, 6Z, 8K, 8T, 9R, 9S or 9Z

Mitrex

Mitrex modules with 30 and 40 mm frames

Mxxx-XYZ

Where "X" can be A, B, I or L; "Y" can be 1 or 3; and "Z" can be F or H

Mitsubishi

Mitsubishi modules

PV-MYYxxxZZ

Where “YY” can be LE or JE; and “ZZ” can be either HD, HD2, or FB

Moltech IM and XS series modules with 40 mm frames

Navitas

Navitas Modules with 35 mm frames

NSMxxx-yyy

Where "yyy" can be 120, 132 or 144

Next Energy Alliance

Next Energy Alliance modules with 35 and 40 mm frames

yyNEA-xxxZZ

where “yy” can be blank or US; “ZZ” can be M, MB or M-60

NE Solar

NE Solar modules with 30, 35 and 40 mm frames

NESExxx-zzAAX-yy

Where "zz" can be 54, 60 or 72; "AA" can be MH or TH; "X" can be blank or B; and "yy" can be M6 or M10

Neo Solar Power

Neo Solar Power modules with 35 mm frames

D6YxxxZZaa

Where “Y” can be M or P; “ZZ” can be B3A, B4A, E3A, E4A, H3A, H4A; and “aa” can be blank, (TF), ME or

ME (TF)

Panasonic (HIT)

Panasonic modules with 35 and 40 mm frames

VBHNxxxYYzzA

Where “YY” can be either KA, RA, SA or ZA; “zz” can be either 01, 02, 03, 04, 06, 06B, 11, 11B, 15, 15B, 16,

16B, 17, or 18; and “A” can be blank, E, G, or N

Panasonic (EverVolt)

Panasonic modules with 30 mm frames

EVPVxxxA

Where "A" can be blank or H, K, HK, HK2 or PK

Peimar

Peimar modules with 40 mm frames

SbxxxYzz

Where “b” can be G, M or P; “Y” can be M or P; and “zz” can be blank, (BF) or (FB)

Philadelphia Solar

Philadelphia modules with 30, 35 and 40 mm frames

PS-YzzAA-xxxW

Where "Y" can be M, MNB, MNG or P; "zz" can be 60, 72, 108 or 144; "AA" can be blank, (BF), (HC),

(HCBF) or (HCBF)-GG; and "W" can be blank or W

MODULE COMPATIBILITY

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 27

Phono Solar

Phono Solar modules with 30, 35 and 40 mm frames

PSxxxY-ZZ/A

Where "Y" can be M, M1, MH, M1H, M4, M4H, M5GF, M5GFH, M6, M6H, M8, M8H, M8GF, M8GFH or P;

"ZZ" can be 18, 20 or 24; and "A" can be F, T, TH, THB, TNH, U, UH, UHB, VH or VHB

Prism Solar

Prism Solar modules with 35 mm frames

PST-xxxW-M72Y

Where "Y" can be H, HB or HBI

Rayzon Solar

Rayzon Solar modules with 35 and 40 mm frames

RSYxxxWC

Where "Y" can be blank or B

Recom

Recom modules with 35 and 40 mm frames

RCM-xxx-6yy

Where “yy” can be MA, MB, ME or MF

REC Solar

REC modules with 30 and 38 mm frames

RECxxxYYZZ

Where “YY” can be AA, M, NP, NP2, NP3, PE, PE72, TP, TP2, TP2M, TP2SM, TP2S, TP3M or TP4; and “ZZ”

can be blank, Black, BLK, BLK2, SLV, 72, Pro M, Pure, Pure-R, Pure-RX or Pure 2

Renesola

ReneSola modules with 35 and 40 mm frames

AAxxxY-ZZ

Where "AA" can be SPM(SLP) or JC; "Y" can be blank, F, M or S; and "ZZ" can be blank, Ab, Ab-b, Abh,

Abh-b, Abv, Abv-b, Bb, Bb-b, Bbh, Bbh-b, Bbv, Bbv-b, Db, Db-b, or 24/Bb

Renogy

Renogy Modules with 35 and 40 mm frames

RZZ-xxxY-AAA

Where "ZZ" can be NG or SP; "Y" can be D or P; and "AAA" can be blank, 144, BB-108, BB-120 or BK-120

Risen

Risen Modules with 30, 35 and 40 mm frames

RSMyy-a-xxxZZ

Where "yy" can be 60, 72, 110, 120, 132 or 144; "a" can be 6, 7 or 8; and "ZZ" can be M, P or BMDG

Saatvik

Saatvik Modules with 35 mm frames

SGExxx-YYYZZZ

Where "YYY" can be 108 or 144; and "ZZZ" can be MHC, MBHC or MHCB

S-Energy

S-Energy modules with 35 and 40 mm frames

SABB-CCYYY-xxxZ

Where “A” can be C, D, L or N; “BB” can be blank, 20, 25, 40 or 45; “CC” can be blank, 60 or 72; “YYY” can

be blank, BDE, MAE, MAI, MBE, MBI, MCE or MCI; and “Z” can be V, M-10, P-10 or P-15

SEG Solar

SEG Solar with 30, 35 and 40 mm frames

SEG-aYY-xxxZZ

Where "a" can be blank, 6 or B; "YY" can be blank, MA, MB, PA, or PB; and "ZZ" can be blank, BB, BG, BW,

HV, WB, WW, BMB, BMA-HV, BMA-BG, BMA-TB, BMB-TB, BMB-HV, BMD-HV, BMB-BG, BTA-BG or BMD-

Seraphim USA

Seraphim modules with 30, 35 and 40 mm frames

SRP-xxx-YYY-ZZ

Where "xxx" is the module power rating; and "YYY" can be BMA, BMD, 6MA, 6MB, 6PA, 6PB, 6QA-XX-XX,

and 6QB-XX-XX; ZZ is blank, BB, BG or HV

Sharp

Sharp modules with 35 and 40 mm frames

NUYYxxx

Where “YY” can be SA or SC

Shinsung E&G

Shinsung Modules with 35 mm frames

SSVxxx-144MH

Silfab

Silfab Modules with 35 and 38 mm frames

SYY-Z-xxxAb

Where "YY" can be IL, SA, LA, SG or LG; "Z" can be blank, M, P, or X; "A" can be blank, B, H, M, N or Q; and

"b" can be A, C, C+, D, G, K, L, M, N, T, U or X

MODULE COMPATIBILITY

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 28

Sirius PV

Sirius PV Modules with 35 mm frames

ELNSMzzM-HC-xxx

Where "zz" can be 54 or 72

Solar4America

Solar4America modules with 30, 35 and 40 mm frames

S4Axxx-YYzzAA

Where "YY" can be 60, 72, 108 or 144; "zz" can be MH5 or MH10; and "AA" can be blank or BB, BW, SW or

STT

Solarever

Solarever modules with 30, 35 mm frames

SE-zzz*yy-xxxM-aaa

Where "zzz" can be 166 or 182; "yy" can be 83 or 91; and "aaa" can be 108, 144 or 144N

Solaria

Solaria modules with 35 and 40 mm frames

PowerA-xxxY-ZZ

Where "A" can be X or XT, "Y" can be R or C; and "ZZ" can be blank, AC, BD, BX, BY, PD, PL, PM, PM-AC,

PX, PZ, WX, WZ or 4T

Solarcity (Tesla)

Solarcity modules with 40 mm frames

SCxxxYY

Where “YY” can be blank, B1 or B2

SolarTech

SolarTech modules with 40 mm frames

AAA-xxxYY

Where "AAA" can be PERCB-B, PERCB-W, HJTB-B, HJTB-W or STU; "YY" can be blank, PERC or HJT

SolarWorld AG

SolarWorld Sunmodule Plus, Protect, Bisun, XL, Bisun XL, may be followed by mono, poly, duo, black, bk, or

clear; modules with 31 and 33 mm frames

SW-xxx

SolarWorld Americas

SolarWorld Sunmodule Plus, Protect, Bisun, XL, Bisun XL, may be followed by mono, poly, duo, black, bk, or

clear; modules with 33 mm frames

SWA-xxx

Sonali

Sonali Modules with 35 and 40 mm frames

SS-M-xxx

Where "M" can be blank or M

Star Solar

Star Solar modules with 35 mm frames

Star-xxxW-YYY-ZZZ

Where "YYY" can be M60H or M60HB; and "ZZZ" can be blank or M10

Stion

Stion Thin lm modules with 35 mm frames

STO-xxx or STO-xxxA

SunEdison

SunEdison Modules with 35 and 40 mm frames

SE-YxxxZABCDE

Where "Y" can be B, F, H, P, R, or Z; "Z" can be 0 or 4; "A" can be B,C,D,E,H,I,J,K,L,M, or N ; "B" can be B or

W; "C" can be A or C; "D" can be 3, 7, 8, or 9; and "E" can be 0, 1 or 2

Suniva

Suniva modules with 35, 38 and 40 mm frames

OPTxxx-AA-B-YYY-Z

MVXxxx-AA-B-YYY-Z

Where "AA" is either 60 or 72; "B" is either 4 or 5; "YYY" is either 100,101,700,1B0, or 1B1; and "Z" is blank

or B

Sunmac Solar

Sunmac modules with 30 and 35 mm frames

SMxxxMaaaZZ-YY

Where "aaa" can be 660, 754 or 772; "ZZ" can be NH or SH; and "YY" can be BB or TB

Sunpower

Sunpower standard (G3 or G4) or InvisiMount (G5) 35, 40 and 46 mm frames

SPR-Zb-xxx-YY

Where "Z" can be A, E, M, P or X; “b” can be blank, 17, 18, 19, 20, 21, or 22; and “YY” can be blank, BLK,

COM, C-AC, D-AC, E-AC, BLK-E-AC, G-AC, BLK-G-AC, H-AC, BLK-H-AC, BLK-C-AC, or BLK-D-AC

MODULE COMPATIBILITY

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 29

Sunspark

Sunspark modules with 40 mm frames

SYY-xxxZ-A

Where “YY” can be MX or ST; and “Z” can be M, MB, M3, M3B, P or W; and "A" can be 60 or 72

Suntech

Suntech modules with 35 and 40 mm frames

STPxxxy-zz/aa

Where "y" is blank or S; and "zz" can be 20, 24, A60, A72U, B60 or B72; and "aa" can be Vd, Vem, Vfw, Vfh,

Vnh, Wdb, Wde, Wd, Wfhb or Wnhb

Talesun

Talesun modules with 30, 35 and 40 mm frames

TAByZZaa-xxx-b

Where "A" can be D, M or P; "B" can be 3, 6, 7 or 9; "y" can be blank, F, G, H, I or L; "ZZ" can be 54, 60, 66,

72 or 78; "aa" can be M, M(H), or P; and "b" can be blank, B, T, or (H)

Tesla

Tesla modules with 40 mm frames

TxxxY

Where "Y" can be H or S

Thornova

Thornova Modules with 30 and 35 mm frames

TS-YYZZ(xxx)-X

Where "YY" can be BB, BG or BGT; "ZZ" can be 54, 60 or 72; and "X" can be blank or X

Trina

Trina Modules with 30, 35 and 40 mm frames

TSM-xxxYYZZ

Where "YY" can be DD05, DD06, DD14, DE14, DE15, DE15V, DEG15, DEG15VC, DE18M, DEG18MC,

DE09, DE19, DEG19C.20, DE06X, PA05, PC05, PD05, PD06, PA14, PC14, PD14, PE14, PE15, NEG19RC

or NE09RC ; and "ZZ" can be blank, .05, .05(II), .08, .08(II), .10, .18, .08D, .18D, 0.82, .002, .00S, 05S,

08S, .20, .20(II), A, A.05, A.08, A.10, A.18, (II), A(II), A.05(II), A.08(II), A.082(II), A.10(II), A.18(II), C.05, C.07,

C.05(II), C.07(II), H, H(II), H.05(II), H.08(II), HC.20(II), HC.20(II), M, M(II), M.05(II), MC.20(II)

Universal

Universal Solar modules with 35 mm frames

UNI-xxx-yyyZZZ-aa

Where "yyy" can be 108, 120 or 144; "ZZZ" can be M, MH, BMH; and "aa" can be blank, BB or DG

URE

URE modules with 35 mm frames

DyZxxxaa

Where "D" can be D or F, "y" can be A, B, 6 or 7; "Z" can be F, K, L or M; and "aa" can be B8G, BFG, BFG-

BB, C8G, DFG-BB, H3A, H4A, H8A, L4A, E7G-BB, E8G, E8G-BB, MFG, MFG-BB or M7G-BB

Vikram

Vikram solar modules with 30, 35 and 40 mm frames

XVSyy.ZZ.AAA.bb

Where "X" can be blank, Hypersol, Paradea, Prexos or Somera; "yy" can be M, P, MBB, MDH, MDHT, MH,

MS, MHBB, or PBB; "ZZ" can be 54, 60, 72 or 78; "AAA" is the module power rating; and "bb" can be 03, 04

or 05

VSUN

VSUN modules with 30, 35 and 40 mm frames

VSUNxxxA-YYz-aa

Where "A" can be blank or N; "YY" can be 60, 72, 108, 120, 132, 144; "z" can be M, P, MH, PH, or BMH; and

"aa" can be blank, BB, BW, or DG

Waaree

Waaree modules with 35 and 40 mm frames

AAyy-xxx

Where "AA" canbe WS or Bi; and "yy" can be blank, M, MB, MD, MDI, MDIB, 33, 55, 57 or 66

Winaico

Winaico modules with 35 and 40 mm frames

Wsy-xxxZa

Where "y" can be either P or T; "Z" can be either M, P, or MX; and "a" can be blank or 6

MODULE COMPATIBILITY

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 30

Yingli

Yingli modules with 30, 35 and 40 mm frames

YLxxxZ-yy

Where "Z" can be D or P; "yy" can be blank, 29b, 30b, 34d, 35b, 36b, 37e 1/2, 37e 1500V 1/2, 40d, 49e 1/2

or 49e 1500V 1/2

Yotta

Yotta modules with 30 and 35 mm frames

YSM-Bxxx-ZZ-72-1

Where "ZZ" can be 06 or 10

Zeus

Zeus Solar Modules with 40 mm frames

ZxxxM-HB

ZN Shine

ZN Shine modules with 30 and 35 mm frames

ZXMY-AAA-xxx/M

Where "Y" can be 6, 7 or 8; "AAA" can be 72, NH120, NH144, NHDB144, NHLDD144, SH108, SH144,

SHDB144, SHLDD144, TP120 or UHLDD144; and "M" can be M or N

MODULE COMPATIBILITY

2024 IRONRIDGE, INC. VERSION 4.3 XR FLUSH MOUNT INSTALLATION MANUAL - 31

MAKE MODELS

FRAMELESS MODULE LIST

Astronergy Solar

Astronergy frameless modules

CHSM6610P(DG)-xxx

Canadian Solar

Canadian Solar frameless modules

CSbY-xxx-Z

Where “b” can be 3 or 6; “Y” is K, P, U, or X; and “Z” can be M-FG, MS-FG, P-FG, MB-FG, or PB-FG

Heliene

Heliene frameless modules

YYZZxxxA

Where "YY" can be72; "ZZ" can be M; and "A" can be GH

Jinko

Jinko frameless modules

JKMxxxPP-DV

Prism Solar

Prism Solar frameless modules

BZYY-xxxAAA

Where "Z" can be i or N; "YY" can be 48, 60, 60S, 72 or 72S; and "AAA" can be blank or BSTC

Risen

Risen frameless modules

RSMyy-6-xxxZZ

Where “yy” can be 60, 72, 120 or 144; and “ZZ” can be MDG or PDG

Stion

Stion frameless modules

STL-xxx or STL-xxxA

Sunpreme

Sunpreme frameless modules

GXB-xxxYY

Where “YY” can be blank or SL

Trina

Trina frameless modules

TSM-xxxYY

Where “YY” can be either DEG5(II), DEG5.07(II), DEG5.40(II), DEG5.47(II), DEG14(II), DEG14C(II),

DEG14C.07(II), DEG14.40(II), PEG5, PEG5.07, PEG5.40, PEG5.47, PEG14, or PEG14.40