— 1 —
Customer Service: 1-877-GET-MAAX (1-877-438-6229).
OLIO 6030 PAN OLIO 6030 BATHTUB
Included – Shower Pan or Tub
3/16"
Drill Bit
Phillips Screw Bit
Tools Needed
Items Included
Read and follow all instructions prior to installing your Maax Bath fixture. Save these instructions for future reference. F
ailure to comply with these
instructions may invalidate your warranty. For questions concerning installation and maintenance of your Maax Bath showeror tub/shower,
contact Technical Services at 1-877-GET-MAAX (1-877-438-6229).
Olio C
ollection Installation Guide
141429 • 141431
NOTICE: Please inspect the unit thoroughly before installation to make sure it has not been damaged during transportation.
Under no circumstances should a damaged unit be installed. Neither Maax Bath nor the distributor will be responsible for
removal or reinstallation costs should a replacement be necessary due to installation of a damaged unit.
— 2 —
Installation Data
OLIO 6030 BATHTUB, OLIO 6030 PAN
1. Review job print and Maax rough-in dimensions; verify all key
dimensions against actual job conditions.
2. In remodeling, if necessary, add studs at each end to provide a
vertical nailing surface for the side nailing anges of bath xture
product.
3. Make sure framed-in framing pocket is of proper size, square and
plumb; check oor for level. Some shimming between the stud
frame and xture may be required.
4. If re-rated framing pocket is required, approved nish material
must be in place prior to unit installation to meet re safety
requirements of local building code and/or FHA/HUD Minimum
Property Standards.
NOTE: Finished framing pocket must have interior dimensions
shown on rough-in diagram to permit installation of unit.
5. Foundation materials are not required for these units.
6. DO NOT install the product over open oor joist. Shimming may
be required for additional support, if suboor is uneven.
7. Tubs require a 6” x 12” oor opening for the 2” IPS drain
connection (See diagram 1 for location). Shower pans require a
6” diameter oor opening.NOTE: Be sure oor opening location
matches left-hand or right-hand bath xture drain location.
8. Make sure all plumbing is complete and to code.
9. To
avoid obstruction, make sure that supply lines and valve
plumbing do not project into framing pocket during the installation
process.
10. To prevent scufng while installing unit, cover the oor of the unit
with a piece of cardboard or other protective material.
11. Fasteners for:
Wood framing – 1 1/2” galvanized roong nails or #10 x 1
1/2” self-tapping washer head screws.
Concrete or block walls – 1” concrete nails and nailing tool.
Steel studs (18 ga.) – drill anges and studs with 5/32”
carbide bit and use #12 x 1” sheet metal screws.
Pre-Installation Planning
*Please read ALL installation instructions completely before beginning.
Check dimensions. NOTE: If you’re adding additional accessories such as
a grab bar–additional framing or backing may be needed for support.
Pre-install unit to ensure framing pocket is plumb, square, and a level installation can be
achieved. (See steps 2 and 3.) Adjust framing as needed – shim where necessary.
6"x12"
AA
AA
C
C
DD
B
B
11
Models A B C D
OLIO 6030
PAN
60
1
⁄8” 31
1
⁄4” 8
1
⁄2” 14
1
⁄2”
OLIO 6030
BATHTUB
60
1
⁄8” 31
1
⁄4” 2” 13
7
⁄8”
Pre-Installation Instructions
*Review Tech Data at maax.com for more detail. NOTE:
O
LIO 6030 PAN is shown for illustrational purposes
Level and mark all sides. Front apron should be rmly on the oor.
NOTE: If unit is not level, the joints and seams will not align properly.
33
Lift and place the base into framing.
22
Customer Service: 1-877-GET-MAAX (1-877-438-6229).
— 3 —
Remove base.
44
Measure the distance between the top of the back horizontal ange and the bottom of
the pan ledge, approximately 1-1/2”. Mark this dimension on the back studs (or wall),
below the rst mark.
55
Installation Data
Fasten a 1” x 3” ledger strip along the rear and sides of framing
(immediately below marks).
66
Install drain assembly per manufacturer’s instructions.
Place base into framing pocket.
77
Tap down until level. Level lengthwise and widthwise using 3 ft. (915mm) level by
shimming, if necessary. The unit must be set level. Front apron should be rmly
on the oor.
99
Assure waste pipe protrudes well into drain tting. (pan install only)
88
Installation Instructions
OLIO 6030 BATHTUB, OLIO 6030 PAN
Customer Service: 1-877-GET-MAAX (1-877-438-6229).
— 4 —
Pre-drill horizontal anges along top of base section and fasten into each corresponding
stud. Pre-drill both (vertical) side anges and fasten to side studs 8” (200mm) on
center. Place cardboard to protect nish.
1010
Installation Data
When other than cementitious backer board plaster is to be used, furring strips as thick as
nailing anges are recommended for installation on studs above the installed unit to assure
walls will be ush. 100% silicone sealant with mildew resistant properties should be applied
between the backer board and horizontal surface of unit. Finishing of other trades should be
done in conformance with applicable codes and general accepted building practices.
1111
Clean-up
CAUTION: DO NOT USE heat or solvent based cleaning
uids. NOTE: Do not remove warranty/maintenance adhered
label. Warranty/User maintenance label must be left for
occupant (Required by ANSIZ124).
1. Prevent staining. Remove all debris before plumbing leak
test. Drain and wipe clean immediately after the inspection process.
Use sponge with warm water and liquid detergent. Rinse, drain
and wipe clean. Do not use abrasive cleansers such as scouring
powders, steel wool, metal scrapers, sandpaper or anything else
that might mar, dull or scratch the nish. Roong tar or paints may
be removed with rubbing alcohol or paint thinner (not lacquer
thinner).
2. Plaster and latex paint may be removed with warm water, liquid
detergent and brittle brush or plastic scraper. Do not use metal
scraper or utensil to remove plaster or paint from nish.
3. Dull areas and light scratches can be restored to high
gloss with white or cream-colored automotive rubbing compound,
followed by application of coat or good quality white automotive
polish (or similar) and buff with a soft cloth. DO NOT WAX
standing surfaces of the unit bottom (this includes textured, slip
resistant standing surfaces), which could result in greater risk of
slipping and personal injury.
4. Major gouges require professional repair.
5. See user maintenance label for more details.
User Maintenance Instructions
IMPORTANT! Use only recommended cleaners and
procedures described herein. Use of other materials and
methods may damage your bath xture and void the
warranty.
1. For normal cleaning, never use abrasive cleaners such as scouring
powders or pads, steel wool, scrapers, sandpaper
or anything else that could scratch or dull the surface of your Maax
unit. Instead, use warm water and liquid detergents
or non-abrasive cleansers, especially those bathroom
cleansers recommended for berglass.
2. To keep your Maax bath xture sparkling clean, apply a
coat of good quality automotive paste wax or polish and buff
to a high shine with a soft cloth or towel. Repeat every six
months for easier cleaning and long lasting protection. DO
NOT WAX standing surfaces of the unit bottom (this includes
textured, slip resistant standing surfaces), which could result
in greater risk of slipping and personal injury.
3. To restore a scratched or dull unit, use an automotive
polishing compound applied with a clean cotton rag. Rub
scratches and dull areas vigorously. Wipe off residues.
Follow with automotive wax treatment described above. DO
NOT WAX standing surfaces of the unit bottom (this includes
textured, slip resistant standing surfaces), which could result
in greater risk of slipping and personal injury.
4. To remove adhesive, try 3-M® natural cleaner, De-Solv-It®
or similar materials. If residues remain, saturate small white
cotton rag with nail polish remover and rub vigorously until
the adhesive dissolves and disappears. These solvents are
highly ammable and must be used sparingly and with
caution. Do not allow solvent to go down the drain. Make
sure not to contact plastic drain grates or other synthetic
materials.
5. Rubber mats: If you use rubber “anti-skid” mat, make sure to
remove it from the unit after each use to avoid harm to the
surface nish.
6. Hard Water: Water in certain regions, if not wiped up after
bathing/showering, may cause fading of some bath xture
colors. This is a natural occurrence beyond Maax’s control.
(See Warranty)
CAUTION: When using any cleaning or polishing materials,
make sure to read and follow all package instructions
carefully. Wear rubber gloves at all times and avoid contact
with eyes, skin, clothing, rugs and furnishings. Make sure all
residues are rinsed off thoroughly.
10040336
2019-10-31
OLIO 6030 BATHTUB, OLIO 6030 PAN
Customer Service: 1-877-GET-MAAX (1-877-438-6229).
