VictronConnect changelog and beta releases

2024-09-13 09:45 1/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

During beta-testing of a new VictronConnect release, its details will be listed at the top of this page.

Once released oﬃcially, all beta release notes are condensed into one full release note.

More information about VictronConnect, including manuals, is here:

https://www.victronenergy.com/panel-systems-remote-monitoring/victronconnect.

Please report bugs and give feedback to these betas via the Disqus comments below. Note that

comments are not public by default, and ﬁrst go to a moderation queue.

Changelog

(Currently available betas are on top. See further below for oﬃcial releases.)

v6.10beta13

2024-09-11

Download links:

iOS: Join TestFlight https://testﬂight.apple.com/join/cvufYMEh

Android ARM64 *

Android x86_64*

Windows 10 and higher

macOS 11 (Big Sur) and higher

Linux AppImage

Notes:

Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Please report bugs and give feedback to these betas via the Disqus comments below. Please note that

comments are not public by default, and ﬁrst go to a moderation queue.

Changes

Add Korean translation

Energy Meter:

Add ﬁrmware v1.08:

Hide L2-L3 line voltage in split phase conﬁguration

This was introduced in v1.07, which was only in VictronConnect beta.

Improve VE.Can communication; this ﬁxes the missing custom name

Solar Chargers:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Fix the issue where “Load output conﬁguration” is not available as an RX port mode setting on

certain models where it should be.

v6.10beta12

2024-09-07

Changes

VE.Bus Inverter/Chargers:

Fix error 122 when updating VE.Bus BMS V2 based systems

Fix system conﬁguration missing phase selection buttons

SmartShunt:

Add support for new models

Lynx Smart BMS:

Improve mode button visibility

Fix maximum starter voltage value for BMV & SmartShunt demos

v6.10beta11

2024-08-30

Changes

Restore the “VictronConnect” name on the splash screens

Orion XS:

Add ﬁrmware v1.05 update (mandatory)

Improve non-volatile memory management by ﬁxing a bug that could cause memory

corruption when ﬂashing the history or settings data. This is yet another improvement on

top of what was done previously on v1.04.

Fix operation time count when Orion XS is not charging (Oﬀ state)

Energy Meter:

Fix phase conﬁguration setting (issue introduced in beta10)

Energy counters renaming/rewording

EVCS:

Network settings rewording

Add new settings

GlobalLink:

2024-09-13 09:45 3/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Add support for new model

MultiHS

Add ESS Settings (now similar to the InverterRS family)

Removed the solar data section

VE.Bus Inverter/Charger:

Fix System conﬁguration does not show Phase selection buttons

Solar Chargers:

Improve behaviour when scrolling solar history graphs.

v6.10beta10

2024-08-09

Changes

Android: Fix ﬁrmware and settings ﬁles are not added to the library when opening from a ﬁle manager

while VictronConnect is not already running

GX products:

Better handle local MQTT connection for Venus versions supportin secured proﬁles

Energy Meter:

Add ﬁrmware v1.07:

Add line-to-line voltages

Add neutral current

Add split phase support (L1/L2)

Add energy registration method

Users can choose between vector (default), arithmetic and absolute

Add roles for EV charger, heat pump, water pump and water heater

Fix missing messages/responses in VE.Can communication

Fix Ethernet state being invalid in VictronConnect

Below changes are already included in v6.08

Lynx SmartBMS:

Add ﬁrmware v1.11

Fix bug that prevented the device from automatically switching on after a low cell

voltage. The Lynx BMS now switches on again when a charge voltage is detected on the

system side. This bug was only in the NG versions.

Add support for the “Pending” state in parallel mode that indicates on the GX that the

BMS is waiting until the battery voltage is within a safe range to connect to the

operational battery bank. The voltage displayed indicates the voltage at which it will

connect.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

v1.10:

Support for parallel BMS systems, which adds redundancy to a system. Detect other

BMSs & optimize behavior for that case - implemented such that in case of no

functional CAN-bus communication between the BMSs everything also works. No

user setting is required for parallel support. Use in combination with Venus OS

v3.40 or later, since that includes the new feature about combining the data into

one total “virtual” bank + use that for DVCC. Paralleling is only possible for models

with the same current rating. Combining Smart Lithium BMSs and Lithium-NG BMSs

is allowed.

Add 3 seconds delay to start-up procedure, for all system types, to detect parallel

BMSs.

Peukert adjusted to 1.02 and charge-eﬃciency to 99.5% for more accurate SoC

calculation.

VE.Bus Inverter/Chargers:

VE.Bus ﬁrmware update: Fix error 123 when updating MultiPlus-II 48/3000/35-32 (already

included in v6.08)

Add ﬁrmware v552

v6.10beta9

2024-08-02

Changes

GX products:

Fix connection to local MQTT via when Venus “Unsecured” proﬁle is selected

Orion XS:

Fix Orion XS page does not open when selecting it on the devices list. This bug also aﬀects the

demo product.

Energy Meter:

On remote connections, improve handling when the number of phases is changed.

v6.10beta8

2024-08-01

Changes

Improve the layout of the main settings page

Various ﬁxes and improvements

GX products:

Fix connection to local MQTT via WebSocket Secure is broken

2024-09-13 09:45 5/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Fix live data values of products freeze after 30 seconds when connected via local MQTT

Orion XS:

Add ﬁrmware v1.04:

Bug ﬁxes

Start displaying warning #67 BMS Connection lost. Previous fw version (v1.03) was

not displaying the warning, even though the warning was internally activated. While

active, the charger will be kept at “Float” state, with a ﬁx 12V output voltage

setpoint.

Improve non-volatile memory management by ﬁxing a bug that could potentially

cause memory corruption when ﬂashing the history or settings data.

Improvements

Remove auto equalisation support. On previous FW versions, when equalisation was

enabled, the charger would perform equalisation every charge cycle, which is not

healthy for the battery. Now only the manual equalisation is supported.

Allow VE.Smart Networking to be conﬁgured over VE.Direct.

Add error #67

Fix Orion XS page does not open when selecting it on the devices list. This bug also aﬀects the

demo product.

Multi RS:

Rename “Withouth batteries” ESS mode to “PV Inverter”

Fix live data on remote connections when working as PV iverter

On remote connections, improve handling when the Multi RS is set or unset to work as a PV

inverter.

MPPT Solar Chargers:

Make ﬁrmware v1.64 mandatory for the following models

SmartSolar Charger MPPT 75/10 (A074)

SmartSolar Charger MPPT 75/15 (A075)

BlueSolar Charger MPPT 75/10 (A07C)

BlueSolar Charger MPPT 75/15 (A07D)

Add ﬁrmware v1.65 for SmartSolar 100/30-12V (A07E)

Extend internal improvements made on v1.64 for all SmartSolar 100/30-12V models.

Add ﬁrmware v3.16:

Fix bug on synchronize charging over CAN when two or more MPPTs are connected. This

could potentially cause the charger to jump absorption every day.

Energy Meter:

On remote connections, improve handling when the meter role is changed.

BMV-712 & SmartShunt:

On remote connections, improve handling when the monitor mode or DC meter type is

changed.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

v6.10beta7

2024-07-13

Changes

Various ﬁxes and improvemente for QR quick connect

Show detailed information if a product is shown as an unknown product in the devices list

Fix an issue where avatar pictures in certain VRM installations are shown rotated

Various ﬁxes and improvements

Energy Meter:

Make L1, L2 & L3 instant readout always visible

GX products:

Add support for security proﬁles (feature not released yet)

Make possible to change security proﬁle and set a password via Bluetooth

Support connection to local MQTT via WebSocket Secure

Do not show the GX in the product info page of attached products

MPPT chargers:

Add support for new models

Multi RS:

Make the “Without batteries” ESS mode only show on beta ﬁrmware

Add extra settings needed for the Without batteries mode

Improve the overview main widget

Add phase rotation settings

Show the AC Input connection status in the overview main widget

Add “Low SOC” alarm

Move mode setting to the general settings menu.

Improbe “On/Oﬀ/Inverter only/Charger only” modes description

Instant readout: Fix AC In & AC Out now working on remote connections when phase is not L1.

Fixes on NS Log

Lynx Smart BMS:

Fix mode button is sometimes misplaced

SmartShunt:

Add support for new models

v6.10beta6

2024-06-28

2024-09-13 09:45 7/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Download links:

iOS: Join TestFlight https://testﬂight.apple.com/join/cvufYMEh

Android ARM64 *

Android x86_64*

Windows 10 and higher

macOS 11 (Big Sur) and higher

Linux AppImage

Notes:

Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Please report bugs and give feedback to these betas via the Disqus comments below. Please note that

comments are not public by default, and ﬁrst go to a moderation queue.

Changes

Fix app unresponsiveness for VRM users with a large number of installations

Make settings lock feature more visible; a lock icon is shown in the settings page even when

lock is not set.

Various UI ﬁxes

GX products:

Enable MQTT on LAN:

When connected to a GX device on LAN, you can now access attached products to

monitor and conﬁgure them.

Enable MQTT on LAN and MQTT (Plain text) on the GX device to activate this feature.

These settings are located in the Settings → Services menu

Future Venus versions will change how this feature can be enabled

Lynx SmartBMS:

Add ﬁrmware v1.09: (Including changes from v1.08 & v1.07)

v1.09

The problem with the 1000A models that a pre-charge error occurred when pre-

charging large capacities at 48V has been solved.

Improved pre-charge performance for all voltages.

v1.08

Initial version for Lynx Smart BMS 500-NG and 1000-NG that supports the Lithium-

NG batteries.

The issue of the BMS waking up from sleep mode when battery is completely

discharged has been ﬁxed.

ATC contact opens during updates. This is to prevent potentially dangerous

situations if an overvoltage occurs during an update.

The issue where the LED and AUX outputs were occasionally turned on for a second

in sleep mode has been ﬁxed.

v1.07

Support for Lynx Smart BMS 1000A which includes following improvements:

Improved current measurement for low currents.

Variable fan speed based on BMS temperature and contactor dissipation.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

MPPT RS:

Add isolation resistance value to the demo product

Multi RS:

Make the “Optimize for feed-in” ESS mode available only for the proper grid codes

Add new grid code related settings

Fix the issue where feed-in disabled reasons do not update on remote connections.

Add sustain voltage settings

Add ESS Ac Power setpoint setting

v6.10beta5

2024-06-03

Download links:

iOS: Join TestFlight https://testﬂight.apple.com/join/cvufYMEh

Android ARM64 *

Android x86_64*

Windows 10 and higher

macOS 11 (Big Sur) and higher

Linux AppImage

Notes:

Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Please report bugs and give feedback to these betas via the Disqus comments below. Please note that

comments are not public by default, and ﬁrst go to a moderation queue.

Changes

Fix crashes when connecting a product via VE.Direct USB. Issue introduced in v6.10beta2

Fix ﬁrmware update notiﬁcation is not cleared after updating the ﬁrmware on remote

connections.

Correct the issue where the selection dialog occasionally displays large gaps between options.

Show proﬁle pictures in the VRM installations list

Fix issues when switching between landscape and portrait modes.

VictronConnect now scales properly on Android when in ﬂoating window mode

VE.Bus Inverter/Chargers:

Make it possible to restore settings after a ﬁrmware update

Energy Meter:

Fix number of phases on instant readout

Lynx SmartBMS NG:

2024-09-13 09:45 9/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Fix battery tab show a white empty page on tablets in portrait mode.

Hide batteries cells details on remote connections, this data is not yet available via VRM.

Multi HS:

Mayour improvements in the main overall widget and in the detailed view.

Multi RS & Inverter RS:

Update alarms and their icons

Phoenix & SUN Inverter:

Add ﬁrmware v1.36:

Add settings lock support

v6.10beta4

2024-05-01

Changes

Energy Meter:

Fix Role, Phase Conﬁguration, and Position settings do not work. This issue was introduced in

v6.10beta3.

v6.10beta3

2024-05-01

Download links:

Changes

Fix QR Quick Connect codes on iOS does not open VictronConnect

Correct the issue where the selection dialog occasionally displays large gaps between options.

Multi RS:

Add AC input connection countdowm (Requires non yet released ﬁrmware)

Add Grid Feed-In conﬁguration (Requires non yet released ﬁrmware)

Add new icons for the grid Disconnection reasons panel

Update grid disconnection reasons

AC Input Control: Add disconnection by SOC condition

Use correct unit for instant readout today's yield

MPPT Solar Chargers:

Add ﬁrmware v1.64:

Internal improvements for 100/30-12V model.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Improve robustness of SmartSolar 75/10 and 75/15 during shutdown and startup.

Improve robustness of SmartSolar 100/20 startup under high solar potential.

Make ﬁrmware v3.15 update mandatory for SmartSolar 250/100 rev2

Energy Meter:

Add ﬁrmware v1.06:

Add LED pulse output to indicate energy ﬂow. Default the LED pulses every 10Wh.

Several ethernet related improvements that should help streamlining the ﬁrmware update

procedure.

Update the bootloader to v1.04 to beneﬁt from the same ethernet improvements as

mentioned above.

EVCS:

Handle properly and show ﬁrmware update errors

Improve robustness of the ﬁrmware updater

v6.10beta2

2024-04-23

Changes

Fix minimum Android version required by the Google Play Store to install the app.

Fix QR Qucick Connect on iOS.

Add PIN code dialog when connecting to a product through QR Qucick Connect.

EVCS:

Add ﬁrmware updating support

MPPT chargers:

Fix settings export/import buttons are not present for some models

v6.10beta1

2024-04-10

Changes

Fix Android navigation buttons sometimes overlaps the bottom of the app

Fix some values are partially drawn oﬀ screen

Fix the app will display a shaded overlay when it disconnects from a product while a dialog box

is open.

Return to the devices list instead of the installations list after a remote ﬁrmware update

Fix an issue where a product may be mistakenly added to the “My Products” list after an

unsuccessful connection attempt.

Add initial support for QR Quick connect (feature not available for users yet)

2024-09-13 09:45 11/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

GX products:

Fix ﬁrmware version is not shown when connected via local network

MultiPlus & Quattro:

Fix an issue that may cause settings ﬁles to be saved improperly, resulting in error #9

(Unexpected number of connected products) when attempting to restore settings.

Add ﬁrmware v510

Energy Meter:

Improve product discovery on LAN

Improve ﬁrmware updates

Multi RS:

Add Grid Code support. (Requires new ﬁrmware not available yet)

v6.09 (Released oﬃcially)

2024-09-10

Download links:

iOS: App Store

Android

Windows 10 and higher

macOS 11 (macOS Big Sur) and higher|App Store

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes

VE.Bus Inverter/Chargers:

Fix error 122 when updating VE.Bus BMS V2 based systems

Fix system conﬁguration missing phase selection buttons

SmartShunt:

Add support for new models

Orion XS:

Add ﬁrmware v1.05 update (mandatory)

Improve non-volatile memory management by ﬁxing a bug that could cause memory

corruption when ﬂashing the history or settings data. This is yet another improvement on

top of what was done previously on v1.04.

Fix operation time count when Orion XS is not charging (Oﬀ state)

Solar Chargers:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Add ﬁrmware v3.16:

Fix bug on synchronize charging over CAN when two or more MPPTs are connected. In

some rare situations this could potentially cause the charger to jump absorption.

Improve behaviour when scrolling 30 day history bar graph

Energy Meter:

Fix voltage between PE and Neutral is not shown.

v6.08 (Released oﬃcially)

2024-08-07

Changes

Orion XS:

Add ﬁrmware v1.04:

Bug ﬁxes

Start displaying warning #67 BMS Connection lost. Previous fw version (v1.03) was

not displaying the warning, even though the warning was internally activated. While

active, the charger will be kept at “Float” state, with a ﬁx 12V output voltage

setpoint.

Improve non-volatile memory management by ﬁxing a bug that could potentially

cause memory corruption when ﬂashing the history or settings data.

Improvements

Remove auto equalisation support. On previous FW versions, when equalisation was

enabled, the charger would perform equalisation every charge cycle, which is not

healthy for the battery. Now only the manual equalisation is supported.

Allow VE.Smart Networking to be conﬁgured over VE.Direct.

Add error #67

MPPT Solar Chargers:

Make ﬁrmware v1.64 mandatory for the following models

SmartSolar Charger MPPT 75/10 (A074)

SmartSolar Charger MPPT 75/15 (A075)

BlueSolar Charger MPPT 75/10 (A07C)

BlueSolar Charger MPPT 75/15 (A07D)

Add ﬁrmware v1.65 for SmartSolar 100/30-12V (A07E)

Extend internal improvements made on v1.64 for all SmartSolar 100/30-12V models.

VE.Bus Inverter/Chargers:

VE.Bus ﬁrmware update: Fix error 123 when updating MultiPlus-II 48/3000/35-32

Add ﬁrmware v552

Lynx SmartBMS:

Add ﬁrmware v1.11

Fix bug that prevented the device from automatically switching on after a low cell

voltage. The Lynx BMS now switches on again when a charge voltage is detected on the

2024-09-13 09:45 13/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

system side. This bug was only in the NG versions.

Add support for the “Pending” state in parallel mode that indicates on the GX that the

BMS is waiting until the battery voltage is within a safe range to connect to the

operational battery bank. The voltage displayed indicates the voltage at which it will

connect.

v1.10:

Support for parallel BMS systems, which adds redundancy to a system. Detect other

BMSs & optimize behavior for that case - implemented such that in case of no

functional CAN-bus communication between the BMSs everything also works. No

user setting is required for parallel support. Use in combination with Venus OS

v3.40 or later, since that includes the new feature about combining the data into

one total “virtual” bank + use that for DVCC. Paralleling is only possible for models

with the same current rating. Combining Smart Lithium BMSs and Lithium-NG BMSs

is allowed.

Add 3 seconds delay to start-up procedure, for all system types, to detect parallel

BMSs.

Peukert adjusted to 1.02 and charge-eﬃciency to 99.5% for more accurate SoC

calculation.

Phoenix & SUN Inverter:

Add ﬁrmware v1.36

Add support for settings lock

v6.07 (Released oﬃcially)

2024-06-07

Download links:

iOS: App Store (Pending of Apple App Store approval)

Android

Windows 10 and higher

macOS 11 (macOS Big Sur) and higher|App Store (Pending of Apple App Store approval)

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes

Lynx SmartBMS NG:

Lynx Smart BMS 1000 NG:Add battery details page

v6.06 (Released oﬃcially)

2024-06-06

Changes

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Fix ﬁrmware update notiﬁcation is not cleared after updating the ﬁrmware on remote

connections.

Correct the issue where the selection dialog occasionally displays large gaps between options.

MPPT Solar Chargers:

Add ﬁrmware v1.64:

Internal improvements for 100/30-12V model.

Improve robustness of SmartSolar 75/10 and 75/15 during shutdown and startup.

Improve robustness of SmartSolar 100/20 startup under high solar potential.

Make ﬁrmware v3.15 update mandatory for SmartSolar 250/100 rev2

Energy Meter:

Add ﬁrmware v1.06:

Add LED pulse output to indicate energy ﬂow. Default the LED pulses every 10Wh.

Several ethernet related improvements that should help streamlining the ﬁrmware update

procedure.

Update the bootloader to v1.04 to beneﬁt from the same ethernet improvements as

mentioned above.

Lynx SmartBMS NG:

Fix battery tab show a white empty page on tablets in portrait mode.

Hide batteries cells details on remote connections, this data is not yet available via VRM.

Phoenix & SUN Inverter:

Add settings lock exceptions

SmartShunt:

Add support for SmartShunt 300A model

v6.05 (Released oﬃcially)

2023-04-25

Changes

Fix Google Play Store reports Android 6 as the minimum Android compatible version instead of

Android 8.

Fix settings ﬁles created by VictronConnect v5.xxx do not load on v6.xx

Fix product id doesn't show for local products in product info page

MPPT chargers:

Fix settings export/import buttons are not present for some models

v6.04 (Released oﬃcially)

2024-09-13 09:45 15/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

2024-04-15

Download links:

Changes

Fix Android navigation buttons sometimes overlaps the bottom of the app

Fix some values are partially drawn oﬀ screen

Fix the app will display a shaded overlay when it disconnects from a product while a dialog box

is open.

Return to the devices list instead of the installations list after a remote ﬁrmware update

Fix an issue where a product may be mistakenly added to the “My Products” list after an

unsuccessful connection attempt.

GX products:

Fix ﬁrmware version is not shown when connected via local network

MultiPlus & Quattro:

Fix an issue that may cause settings ﬁles to be saved improperly, resulting in error #9

(Unexpected number of connected products) when attempting to restore settings.

Add ﬁrmware v510

v6.03 (Released oﬃcially)

2023-03-18

Changes

VE.Bus inverter/chargers:

Fix settings of individual units of a conﬁgured parallel of multi phase system can't be accessed

v6.02 (Released oﬃcially)

2023-03-16

Changes

Multi RS:

Fix passthrough mode is not available for selection

GlobaLink520:

Fix update feed setting

v6.01 (Released oﬃcially)

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

2023-03-14

Changes

Android:

Fix Application Not Responding(ANR) seen on certain conbination of hardware/settings/installed

apps. The ANR can happen randomly but trying to start a ﬁrmware update always triggers it on

aﬀected installations.

v6.00 (Released oﬃcially)

2024-03-13

Changes

New Feature: Settings Lock

Installer-Enabled Settings Lock: Now, installers can set a password to lock settings,

ensuring that end-users cannot accidentally modify critical conﬁgurations on their systems.

Easy Unlocking: Unlocking the settings is a breeze. VictronConnect remembers all seen

passwords and auto unlocks the product while the installer is connected.

When you log into VRM, the product passwords are securely stored in VRM and

synchronized across all your devices—phones and computers—where you are logged into

your VRM account.

Firmware Update Required: Settings Lock feature requires compatible ﬁrmware. Firmware

updates for the products supporting this feature are included in this VictronConnect version.

Qt Framework Upgrade: Marks a signiﬁcant milestone as we transition from Qt 5 to Qt 6. This

update brings numerous improvements and advantages that enhance your user experience and set

the stage for new features in the future.

Minimum OS version requirements:

Android:

Android 8 or higher: (previously Android 5)

For older versions VictronConnect v5.106 is available in Victron Energy downloads

page.

iOS:

iOS 14 or higher (previously iOS 12)

Microsoft Windows:

Windows 10 or higher. (previously Windows 7)

For older versions VictronConnect v5.106 is available in Victron Energy downloads page.

macOS:

macOS Big Sur (11) or newer (previously macOS Sierra (10.12))

In the settings page, prioritise Bluetooth ﬁrmware update available notiﬁcation.

On Windows, notify that there is a VictronConnect update and provide a manual update option.

Fix notiﬁcations drawer can partially hide oldest notiﬁcation in certain circumstancies.

Retain alarm notiﬁcations until the user has read them.

2024-09-13 09:45 17/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Demos: Show Bluetooth Enable/Disable for products supporting it.

Improve information shown when a new ﬁle is manually added to the ﬁrmware library

Several UI/UX improvements

Various internal improvements

Multi RS, Inverter RS && MPPT RS:

Add ﬁrmware v1.16:

Check this Victron professional post for detailed changelog.

Inverter RS & Multi RS:

Improve alarms behaviour

Add “Oﬀ reasons” button and notiﬁcations. This shows an explanation of why the

inverter/charger is in oﬀ state.

Add descriptions to the operation modes setting

Add PV inverter yield to the solar history

Add “Short circuit” alarm notiﬁcation.

Add manual control functionality for the built-in relay.

Make system conﬁguration available in demo products

Show each tracker power in the overview page besides with the total PV power. This information

was only available in the status page.

Multi RS:

Fix overview power readout when unit is in L2 or L3 on 3P systems

Input voltage on demo product

Add support for the generator start/stop control using the built-in relay

AC Input control: Fix DC condition connection delay

EV Charging Station:

Add all set of settings that are currently available via the web interface.

BMV-712, BMV-710h & SmartShunt:

Add ﬁrmware v4.16 update:

Fix: settings lock key&timestamp are preserved when performing a restore to default.

Include all changes from v4.15:

Add new feature “Settings lock”.

Add manual control functionality for the built-in relay. (BMV only)

VE.Direct Smart Dongle:

Add ﬁrmware update v2.50:

Add new feature “Settings lock”.

Several small VE.Smart Networking improvements.

SmartShunt, BMV-712, SmartSolar and Smart Inverter:

Add Bluetooth ﬁrmware update v2.50:

Improve Settings lock feature

Several small VE.Smart Networking improvements

Smart Chargers:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Fix descriptions of errors #14 & #18

Add relay manual control mode

Add manual control functionality for the built-in relay. (Only for models with buitl-in relay)

Solar Chargers:

Add Bluetooth ﬁrmware v2.49:

Add new feature “Settings lock”.

Several small VE.Smart Networking improvements.

Add ﬁrmware v1.63:

Add new feature “Settings lock”.

Add support to relay manual control

Add ﬁrmware v3.15:

Add new feature “Settings lock”.

Add support to resetting error 119 by restoring settings to default

Reduce change of mis triggering PV Input shutdown errors

Fix “Lifetime total” & “Since reset” yield does not show in some screen conﬁgurations.

Add manual control functionality for the built-in relay.

Orion Smart:

Add “Oﬀ reasons” button and notiﬁcations. This shows an explanation of why the product is in

oﬀ state.3

VE.Direct Inverter & SUN inverter:

Add ﬁrmware v1.35:

Range “ECO mode search interval” extended to 1 hour

Lynx Smart BMS:

Add distributors to the demo product

Orion XS:

Fix DC input values don't update on remote connection

Fix “Bulk” state is shown instead “External control”

VE.Bus Smart Dongle:

Add ﬁrmware v1.18:

Fixed MultiPlus-II 12/3000/120-50 120/240V details tab shows large negative current on

AC-Out L2 when inverting or with single phase grid connection

Add Ve.Bus error code 128 “Connection prevented by failing relay test”

v5.107 (Released oﬃcially)

2024-03-16

Changes

Windows only:

2024-09-13 09:45 19/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Do not update to v6.xx when running on Windows 10 32-bit

v5.106 (Released oﬃcially)

2024-03-13

Changes

Windows only:

Prevent auto updating to v6.xx updates on Windows 7/8. Latest VictronConnect version is not

compatible with these Microsoft Windows versions.

v5.105 (Released oﬃcially)

2024-02-21

Changes

OrionXS:

Add Orion XS ﬁrmware v1.03:

Add full support to VE.Smart Networking (remote sense).

v5.104 (Released oﬃcially)

2024-02-13

Changes

Fix error #R2 when connecting to remote products.

OrionXS:

Add demo product

Multi RS & MPPT RS:

Add an option to customize the names of MPPT trackers.

Multi RS:

Fix overview widget doesn't show AC input power when the unit is set to L2 or L3

Lynx Smart BMS:

Fix missing settings in demo product

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

v5.103 (Released oﬃcially)

2024-01-17

Changes

Update the “where to ﬁnd the pin code” message shown to the user while connecting via

Bluetooth. It now includes instructions to look for the Bluetooth pin code on a label on device.

Improve stability and speed of ﬁrmware updates on iOS

Fix connection for Android devices using UNISOC T SOC hardware.

OrionXS:

Add ﬁrmware v1.02

Change the displayed product name from Smart BuckBoost to Orion XS

Fix issue that could cause Error 120.

SUN Inverter:

Fix ECO search interval setting, it was not shown.

v5.102 (Released oﬃcially)

2024-01-08

Changes

VE.Bus Inverter/Chargers:

Add ﬁrmware v509 for Quattro-II (2651xxx and 2645xxxx)

Fixed the issue that with ﬁrmware revisions 504-508 a Quattro-II system could end up in a

situation that it refuses to connect to the grid for no apparent reason.

Fix import settings does not work for some new models.

Multi RS & Inverter RS:

Fix AC input current limit and relay high voltage value settings are not included when exporting

settings to a ﬁle.

Fix number of decimals for PV current for units with more than one MPPT tracker

v5.101 (Released oﬃcially)

2023-12-15

Download links:

iOS: App Store(Pending of App Store approval)

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store (Pending of App Store approval)

2024-09-13 09:45 21/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes

VE.Bus Inverter/Chargers:

Fix Quattro-II ﬁrmware v508 ﬁles.

Orion XS:

Use the correct name for this range of products

Victron Energy Meter:

Add ﬁrmware v1.05:

Add position setting

Inverter RS & Multi RS:

Show consumption in 30-Day history

v5.100 (Released oﬃcially)

2023-12-12

Changes

VE.Bus Inverter/Chargers:

Add VE.Bus Inverter/Charger ﬁrmware v508

Phoenix inverter:

Support enlarged ECO search interval on new ﬁrmwares, now 3600s, previously 360s. This

requires a new ﬁrmware not included in VictronConnect yet.

SmartLithium:

Fix instant readout cell voltages do not update requiring to trigger a scan to get updated values

v5.99 (Released oﬃcially)

2023-11-14

Download links:

Changes

Fix battery monitor ﬁrst use setup can't be completed (issue introduced in v5.98)

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

v5.98 (Released oﬃcially)

2023-11-13

Changes

Multi RS, Inverter RS & MPPT RS:

Add ﬁrmware v1.15 (mandatory upon connection)

Update fan and dimming temperature proﬁles, enable the fan earlier for the MPPT circuit.

VE.Bus Inverter/Chargers:

Fix ﬁrmware update when updating systems with more than 4 units

Fix ﬁrmware update when updating MultiPlus-II systems with multiple hardware ids

Add ﬁrmware v507 for some MultiPlus-II models

Fix noisy/erroneous fan driving for

MultiPlus-II 24/3000/70-32 (PMP242305010); HQ2229 Up to and including HQ2337

MultiPlus-II 48/3000/35-32 (PMP482305010); HQ2226 Up to and including HQ2339

MultiPlus-II 48/5000/70-50 (PMP482505010); HQ2225 Up to and including HQ2317

Not all units within those serial number range are aﬀected. For further details, see change

log on Victron Professional.

Victron Energy Meter:

Add initial support

Smart BuckBoost:

Add initial support

SmartLithium:

Improve Instant Readout when low & high cells are out of range

v5.97 (Released oﬃcially)

2023-10-04

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes

2024-09-13 09:45 23/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

SmartShunt / BMV-712:

Add Bluetooth ﬁrmware v2.46:

Fix for occasional erroneous battery temperature broadcasts on VE.Smart networking,

causing Smart Solars (on the same network) to stop charging.

Add support for VE.Smart Networking for new IP65 Rev2 Smartshunts.

Fix for SOC trend scaling error. In some situations a wrong SOC value could end up in the

stored trend for SOC (only the stored trend; the SOC value itself was not aﬀected).

v5.96 (Released oﬃcially)

2023-09-25

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes

Fix issues with ﬁrmware updates on the recently released Apple iOS 17.

VE.Bus Smart Dongle:

Add VE.Bus Smart Dongle ﬁrmware v1.17

Improve sustain state reporting

SmartSolar:

Fix settings import/export for SmartSolar 75/15 & SmartSolar 75/10 rev3 models

v5.95 (Released oﬃcially)

2023-08-30

Changes

Fix Bluetooth connection on some Android Phone models

Fix VRM remote connection on Windows; You may need to re-authenticate in VRM.

v5.94 (Released oﬃcially)

2023-08-29

Changes

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Fix Bluetooth connection with GX, EVCS and GlobalLink 520 products.

v5.93 (Released oﬃcially)

2023-08-25

Changes

Fix VRM login on Windows

Fix issues with iPad Pro 2016 WiFi

Show Bluetooth Instant Readout key and product MAC address in Product Info page

Improve service report content

Fix remove button in ﬁrmware list for user added ﬁles

Android: Do not ask for permission to open non supported USB devices.

VE.Bus Inverter/Charger:

Add new MultiPlus models

Fix sustain voltage is not saved into settings ﬁles

MultiRS:

Allow “0” as minimum number of inverters to start on three phase systems

Do not show parallel system conﬁguration option. Parallel conﬁguration is not supported yet.

v5.92 (Released oﬃcially)

2023-08-09

Changes

Fix issue with iPad Pro 2016 WiFi

SmartSolar:

Add ﬁrmware v3.14 for SmartSolar 250/100 rev2 model. (mandatory):

Improve the PV short relay reset mechanism

VE.Bus Smart Dongle:

Add ﬁrmware v1.16:

Add sustain state to instant readout

Add support for solar and wind priority feature

Add support for “Solar and wind priority” controls

VE.Bus Inverter/Charger:

Add ﬁrmware v506

Add support for “Solar and wind priority” settings and controls

Fix product info page does not always notify that there is a ﬁrmware update available

2024-09-13 09:45 25/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Smart BMS:

Add ﬁrmware v1.09:

Improved power-up sequence for System+ port

Added support for HW rev2

Added System+ LED control

Added Alternator LED control

Disallowed product release in Test mode, when HW rev2 is not set

Set minimum App version to v1.09 for HW rev2 products

v5.91 (Released oﬃcially)

2023-06-05

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes

Add a feature to lock VictronConnect on to a demo product. Useful for exhibitions and training.

Multi RS & Inverter RS:

Add ﬁrmware v1.12:

Changes applying to Inverter RS only:

Add support for AC output parallel and 3-phase operation.

Changes applying to Inverter RS and Multi RS only:

Fix false-positive over-charge protection (error 29).

Fix false-positive PV riso protection (errors 41 and 42).

Remember the operating mode (on/oﬀ/inverter only) during a ﬁrmware update.

Instead of always switching On after a ﬁrmware update.

Fix PV panel power/current readout in case the MPPT converter is oﬀ, there can still

be current present if the panel voltage is too high.

Changes applying to Multi RS only:

Add pass-through mode, this closes the AC input relay while the inverter/charger

remains oﬀ, the MPPT charger remains active. Settable in VictronConnect.

Add 'External control' support, this allows for self implementation of a control loop

by controlling the AC power set-point dynamically.

Improve inverter PLL to prevent frequency jumps when the AC input is connected or

disconnected, this could trigger a PV inverter disconnect.

Ignore conditional AC disconnect in sustain mode and inverter shutdown due to

allow-to-discharge signal.

Changes applying to Multi RS dual-MPPT (PMR482602020) only:

Fix relay test sequence.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Remove PE-Neutral monitoring.

VE.Bus Inverter/Charger:

Fix ﬁrmware version reports that it is up to date when it isn't.

Add new models

VE.Bus Smart Dongle:

Add support for Quattro-II 2x120V

Fixed spurious AC input frequency values during inverting.

With some Multi models occasionally spurious AC input frequency values where published

during the inverting state.

Fixed missing values updates with instant readout enabled.

While connected, with instant readout enabled, not all values where properly updated on

changes.

v5.90 (Released oﬃcially)

2023-05-02

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes

Instant readout now notiﬁes warnings, alarms and errors

Improve stored trends time-stamp accuracy of data stored before a reboot

Improve service log mechanism to include more useful data in service reports

VC-R: Fix a bug that makes VE.Bus Inverter/Chargers to be listed when the GX product is

running Venus v3.0. These products are not supported by VC-R.

Fix Bluetooth problems with Nokia G11, Samsung Tab A8 and probably other Android models.

Fix settings with radio buttons can report a wrong value after when pressing the cancel button.

This issue didn’t aﬀect the actual value of the setting.

Multi RS:

Improve and add extra information to ESS mode selection

Hide “Monitor PE to Neutral voltage” setting for models not supporting it

Add new aux input modes

Trends: Fix AC out power does not report data

VE.Bus Inverter/Chargers:

Support ﬁrmware updates using multiple vﬀ ﬁles. Some models depending on production date

2024-09-13 09:45 27/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

report diﬀerent product ids and the proper ﬁrmware ﬁle is required for each product id.

Add ﬁrmware v503 for some models:

See ﬁrmware details here

VE.Bus BMSv2 false detection when previously connected to a system with a BMS

Add missing VE.Bus errors

Improve recovery from a BMSv2 failed ﬁrmware update including both BMS & Inverter

simultaneous ﬁrmware update failure and some other corner cases.

VE.Bus Smart Dongle:

Fix default PIN code warning when dongle is connected to a Multi/Quattro

Fix VE.Bus settings load and restore for the “DC input low pre-alarm” setting:

In case the DC input low-shutdown value was modiﬁed the “DC input low pre-alarm” could

contain the wrong value.

Smart Battery Protect:

Add ﬁrmware v2.11:

Added support for Instant Readout

VictronConnect can now show the most relevant Smart BatteryProtect data in the product

list page without having to stablish a connection

Improved “Disabled SBP will now try to pull output to 0V” behavior (introduced in v2.06)

To prevent possible mosfet failures

SmartBMS & SmartBMS CL:

Add ﬁrmware v1.08:

Added support for Instant Readout

VictronConnect can now show the most relevant Smart BMS Current Limiter data in

the product list page without having to establish a connection

Removed BMS cable error detection

The detection could give false cable error detections when more than 1 battery was

connected. This could lead to a lock-up, because charging and discharging is not

allowed anymore in that case. The detection has been removed because it is

impossible to detect a faulty BMS cable when there is more than one battery

connected.

Added support for Random PIN codes

Made sure that allow charge/discharge outputs (&LEDs) stay active at end of FW update

Several internal improvements

Smart BMS 12-200 only:

Added Alternator-Only as remote-oﬀ option making it possible, to disable only Alternator when

Remote OFF.

Disabling both Alternator and System+ port can still be selected as remote-oﬀ option.

Added charge current limiting for the charge current coming from the System+ port. Previously,

the conﬁgured limit was used for the Alternator charging only.

EVCS:

Add demo products

VE.Direct Smart Dongle, SmartSolar & SmartInverter:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Add Bluetooth ﬁrmware v2.44:

Fix VE.Smart networking and custom name not being cleared when “Restore default” for

product is executed. Now, the only things not cleared by a restore default, on purpose,

are Bluetooth pincode and bluetooth bonding.

Fix: erratic values in battery temperature trend data (only applicable for SmartSolar).

Fix: short interruption in the battery temperature trend data when charging stops (only

applicable for SmartSolar).

Some small VE.Smart Networking improvements

SmartLithium:

Add ﬁrmware v1.31:

Add support for hardware revision 2

Solar Chargers:

Fix wrong error #26 description

v5.83 (Released oﬃcially)

2023-04-05

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes

Add Ukrainian translation

SmartShunt:

Add ﬁrmware v4.14:

Fix for lost ﬁrmware. In rare situations the SmartShunt would require a ﬁrmware update

after a cold boot (powerup). When this happened, the functionality of the Smartshunt was

fully restored by completing the update. There was no impact on the History and the

Settings i.e both remained unaﬀected by this issue.

Fix for failing updates. In some rare situations the update was aborted due to an

unexpected internal hardware event.

BMV-712/710H:

Add ﬁrmware v4.13:

Fix for incorrect calculated state of charge (SOC) when no temperature sensor is

connected while the auxiliary input is set to “Temperature”. This issue was found in v4.12

and could in extreme cases result in a SOC that is always 1%.

2024-09-13 09:45 29/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

BMV-710: Since latest released ﬁrmware for this model was v4.05 , with the v4.13 update

the BMV-710H gets all the ﬁxes and features from intermediate versions like DC monitor

mode and retained SOC on reset.

Orion Smart:

Add ﬁrmware v1.13: (Update is only mandatory for models aﬀected by the issue described

below)

Fix issue on some isolated 24V output models that don’t startup on low temperatures.

v5.82 (Released oﬃcially)

2023-02-15

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes

RS products:

Add RS ﬁrmware v1.11:

Changes applying to all RS products (Inverter RS, Multi RS and MPPT RS):

Report warnings and alarms on the internal display.

Remove upper limit from the battery tail current setting. When pairing multiple

chargers together this setting can be larger than the units' own maximum current

value.

Changes applying to Inverter RS and Multi RS only:

Improve PV isolation measurement and PV residual current detection test sequence

to avoid false positive detections.

PV residual current sensor self-test failure now reports as error code #202.

It is now possible to switch oﬀ the backlight of the internal display using the latest

VictronConnect app.

Fix low SOC alarm, no longer using the discharge ﬂoor and internal non-editable

90% level to generate the alarm. The low SOC alarm only uses the low SOC

shutdown settings.

Fix low battery voltage alarm when powering up the unit by connecting the battery.

Report the inverter power as Watts instead of VA and add inverter current on the

built-in display.

Changes applying to Multi RS only:

Add support for generators:

The inverter has an increased tolerance for irregularities on the ac input like

fast frequency changes or voltage changes. For robust generator control

enable 'moderate generator load changes' and switch oﬀ the 'UPS function'.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Add 'moderate generator load changes' setting, enabling this lets the inverter

absorb sudden load changes and slowly transfer them to the generator. This

prevents speed variations in the generator.

Add 'UPS function', this realizes a faster transfer to inverter mode when the mains

stops. This function is enabled by default.

Reduce charge current at higher battery voltages and/or lower AC input voltages. At

230V, the maximum charge current at 57.6V is now approximately 88A unless

derated due to ambient/internal temperature. The maximum achievable charge

current was higher, approximately 95A under the same conditions.

Update Battery Life state if the minimum discharge soc setting is lowered externally

during operation.

Fix low SOC shutdown behavior, it did not take the AC input into account.

Add conditional AC input disconnect feature.

Clear PE-Neutral error condition when disconnecting from the grid, this allows for

easy mains plug reversal to ﬁx this issue.

BMS discharge current limit 0 shuts down the unit when it operates in inverter

(island) mode, any other value resumes normal operation.

Setting the on/oﬀ mode to 'Inverter only' now disconnects from the grid, in line with

the VE.Bus Inverter/chargers.

Change behavior of the battery state 'sustain' (=battery discharged). In ESS mode

'optimized' the unit switches to trickle charge mode where previously it would

charge the battery at full power from the grid.

Improve mains plug disconnect detection reliability for systems that are not allowed

to feed energy to the grid. This is realized by always drawing a small current from

the grid, so we can reliably detect grid absence.

Improve remove on/oﬀ pass-through when using the SmallBMS. Before the system

would also ﬂag that the battery is discharged.

Multi RS:

Fix AC input current scaling

VE.Bus Inverter/Chargers:

Add ﬁrmware v502

EVCS:

Improve notiﬁcations related to not-conﬁgured modes

Make possible to disable WiFi network scanning

Fix misbehaviour of notiﬁcations panel

Battery monitor:

Keep SOC on reset: Move “Keep SOC” to the top of options list

Add BMV-712 rev2 to settings deﬁnitions. Enables save/load settings ﬁles.

Add retained soc capability to BMV & SmartShunt demos

SmartLithium:

Set minimum ATC temperature to 0ºC

2024-09-13 09:45 31/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

v5.81 (Released oﬃcially)

2023-01-18

Changes

SmartShunt & BMV-712:

Add Bluetooth ﬁrmware v2.43:

Adds new “Keep SOC on reset” feature. (!) Selectable in battery settings.

Fix (rather rare) bug that could cause faulty temperatures to be transmitted in a VE.Smart

network. This bug only aﬀected BMVs and SmartShunts without the (optional)

temperature sensor. These “zombie” temperature broadcasts caused SmartSolars to stop

charging for the rest of the day, to restart only the next day. Note that this bug was very

rare to occur.

Orion Smart:

Add ﬁrmware v1.12:

Add instant readout

SmartSolar & BlueSolar:

Update shipped ﬁrmware to v3.13 (was v3.11):

Show error 2, Battery voltage too high, immediately when powering up. Instead of only

once starting to charge. This allows the installer to see an issue, by for example

recognising odd blinking LEDs, easily and before connecting the PV.

Split error 38 into error 80 to 87. The error description can be found at

https://www.victronenergy.com/live/mppt-error-codes.

Reduce possibility of mis triggering the PV short protection.

Add feature to reset the PV short for SmartSolar VE.Can 250/100 (PV Short relay was

introduced per HQ2150)

VE.Bus Inverter/Chargers:

Add ﬁrmware v501

SmartLithium:

Add support for new models

v5.80 (Released oﬃcially)

2022-12-14

Changes

No longer require the connected device to be updated to the latest ﬁrmware in order to be able

to see and modify its settings. Minimum ﬁrmware versions (for accessibg the settings) for a few

main product lines now are, and will remain to be:

MPPT Solar Chargers: v1.59 / v3.10

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

BMV-712 and SmartShunt: v4.11

BMV-700 and BMV-702: v3.11

Orion Smart series: v1.10

Blue Smart Chargers IP22: v3.21 & v3.42(rev2)

Blue Smart Chargers IP65: v3.25

Blue Smart Chargers IP65 (6V/12V): v3.42

Blue Smart Chargers IP67: v3.21 & v3.25(rev2)

Lynx Smart BMS: v1.05

Multis and Quattros: no minimum version

Fix alarms drawer opens full size when connecting to a product with an active alarm

Add Polish and Japanese translations

Improve UX on product info when already at latest version

Electric Vehicle Charging Station (EVCS):

Add initial support via Bluetooth. Requires a new ﬁrmware version that is not publicly available

yet.

Multi RS:

Changes that require a new ﬁrmware that is not publicly available:

Add UPS function setting

Add “Moderate generator load changes” setting

Split the “minimuim inverters to operate” functionality in two settings

Fix inconsistency on how frequency is shown for AC Out 2

Use correct AC out power when AC IN relay is open

Show AC currents

Use grid layout for live data items

Add new errors

Remove “External control” ESS mode. This mode is not available yet.

Warn before updating that the inverter will switch oﬀ during a ﬁrmware update and explain how

to keep AC loads powered

Hide ESS menu from demo product

MPPT/Inverter/Multi RS:

Allow NMEA2000 instance number change

Add option to reset BMS control

VE.Bus Inverter/Chargers:

Add ﬁrmware v500. (optional)

Add a setting to disable VSense

Add instant readout functionality

Implement BMS v2 ﬁrmware update mechanism

Add BMSv2 ﬁrmware v113 (optional)

VE.Bus Smart dongle:

Add ﬁrmware v1.13: (optional)

Add Support for instant readout

Improve number of values shown in secondary mode. Secondary mode now shows AC

input an output voltages, currents, frequencies and power values.

2024-09-13 09:45 33/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Add instant readout functionality

Lynx SmartBMS:

Fix alarm notiﬁcations keeps popping up while alarm is active.

Add ﬁrmware v1.06:

Increase reserve capacity: the capacity that remains in the battery when the system

shuts itself down to prevent further discharge. This reserve capacity deﬁnes the time

(number of weeks) that is available before at the latest having to recharge the battery to

prevent a too deep discharge. Two changes:

When the Lynx Smart BMS (LSB) auto-shuts down to prevent further discharge (ATD), due

to a low cell event, the main contactor and the GX device (aux output) are shutdown with

a delay. This delay was 2 hours, which is now reduced to 5 minutes. The reason behind

the 5 minutes, as opposed to doing that immediately, is to allow for sending the shutdown

reason to the VRM remote monitoring portal. The related low cell voltage threshold is

conﬁgured in the batteries.

When the LSB auto-shuts down due to the low SOC protection, the LSB used to shut down

the loads (ATD contact) but keep the main contactor as well as GX device powered. Until

a low cell voltage event occurred. Now, it uses the same mechanism as on a low cell

voltage event: upon reaching the SOC threshold, the loads are shut down (ATD contact)

immediately. And after a 5 minute delay the GX device (AUX output) and main contactor

are shut down as well. Unless it measures a charge current of 500mA or higher. This

ensures the lowest possible power consumption for the BMS of only 0.3mA for all system

voltages.The related SOC threshold is conﬁgurable in the BMS.

Improved wakeup behavior when the system was shut down due to low battery voltage,

low cell voltage or low SoC. With previous versions, the system wakes up when the

charging voltage is 0.5V higher than the battery voltage. Now that we turn OFF the BMS

earlier and the solar chargers lose their BMS connection, the output voltage of the solar

chargers will be 12V (on 12V systems). To be sure the BMS turns ON at sunrise, we have

added a new wake-up reason: if the charging voltage is above 11.7V. This is 23.4V for 24V

systems and 46.8V for 48V systems.

Two seconds delay added to (not-)allowed-to-discharge to prevent unexpected load

disconnect at glitches on the Smart Lithium BMS signals.

SmartLithium:

Fix “E-SL1 Overvoltage alarm” should be “E-SL1 Balancer failure”

SmartShunt:

Add speciﬁc icons for IP65 models

MPPT Solar Chargers:

Remove RX port function settings in demo products of models that doesn't support them.

Add ﬁrmware v3.11 & v1.61: (optional)

Improve battery voltage auto-detect corner cases, by completely eliminating the chance

of a charger running with an auto-detect pending after the next restart or power cycle.

Three changes: (1) in case the charger can’t detect the battery voltage, because no

battery voltage is present at power-up on the battery terminals, select 12V. (2) after

doing a restore settings to default, perform an auto-detect after 10 seconds. The 10

seconds is to allow a distributor to power down the product in order to leave the product

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

as if its fresh from the factory. (3) Models without load-output would do an auto-detect

only if there is PV present. This is changed: auto-detect happens always within 10

seconds after power-up, unconditionally and same for all models.

SmartSolar Control display: no longer show the battery voltage setting on the display at

ﬁrst power-up, to simplify the process and interaction with auto-detect. The setting is still

available in the settings menu.

Add support to relay remote control mode, which allows the user to manually select the

relay state.

Add a button to reset the PV short relay:

Only for SmartSolar 250/100 VE.Can

Requires a new ﬁrmware that is not oﬃcially available yet.

BMV7-12 & SmartShunt:

Add ﬁrmware v4.12: (optional)

Prepare for Keep SOC on reset feature

SmartBatterySense:

Fix ﬁrmware update availability is not reported for SmartBatterySense rev2 models

v5.77 (Released oﬃcially)

2022-11-02

Changes

VE.Bus Inverter/Charger:

Add ﬁrmware v499 for Quattro 48/10000/140-2×100 & Quattro 48/8000/110-2×100 (optional)

Multi RS:

Fix inconsistency on how frequency is shown for AC Out 2

MPPT solar chargers:

Remove RX port function settings in demo products for models that doesn't support them.

v5.76 (Released oﬃcially)

2022-10-24

Changes

Fix various demo products

VE.Bus Inverter/Charger:

Add support for VE.Bus inverter/charger ﬁrmware v498

2024-09-13 09:45 35/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Include VE.Bus inverter/charger ﬁrmware v498 (optional update)

v5.75 (Released oﬃcially)

2022-10-13

Changes

Fix Cerbo-S GX is recognised as a diﬀerent product

v5.74 (Released oﬃcially)

2022-09-26

Changes

Fix internal products database keeps adding duplicated entries under certain conditions

Fix in range products serial numbers are shown as “undeﬁned” in VE.Smart networking conﬁg

page.

Notify when there is a ﬁrmware update available for the Bluetooth interfaces

Android: Internal improvements

Fix fetching trends data on reconnect

Enable PIN code reset via PUK to all internal dongles

Reword “broadcast data” to “instant readout”

MPPT Solar Chargers:

Require conﬁrmation when user changes the battery voltage

Make sure to exit from voltage auto detection when user selects battery voltage

Fix history CSV export can fail in certain situations

SmartSolar, BMV & SmartShunt:

Set Bluetooth ﬁrmware v2.41 as optional update

Phoenix Inverter:

Fix load widget shows “0” instead of load state

SUN Inverter:

Fix history CSV export

VE.Bust Smart Dongle:

Fix connected Multi/Quattro is not added to “My devices”

Orion Smart:

Reword “Charger enabled” to “Output enabled”

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

SUN Inverter:

Enable settings ﬁle export/import

Fix “Low battery shut down” and “Low battery restart & alarm” settings

BMV-712 & SmartShunt:

Add option to retain SOC after a power cycle. This requires a new ﬁrmware that will be available

soon.

Fix current reading in demo produts

v5.73 (Released oﬃcially)

2022-08-18

Changes

Remove tail current maximum value limitation as it is not high enough for big batteries banks.

Now the user can set any value and the product will clip it to boundaries if necessary. Applies to

BlueSolar, SmartSolar, Multi/Inverter/MPPT RS, Smart Lynx BMS and SUN Inverter.

Always show the broadcast data expand button, this allows to toggle the description text when

all the data ﬁts in one line.

GX products:

Fix the GX device is not added to “My devices” when using Bluetooth.

VE.Direct Smart dongle:

Add ﬁrmware v2.41: (update mandatory upon connection)

Add Bluetooth live data advertisement support

Smart Phoenix Inverter:

Add bluetooth ﬁrmware v2.41: (update mandatory upon connection)

Add Bluetooth live data advertisement support

Lynx Smart BMS:

Add a disable/enable switch to the discharge ﬂoor setting.

Add description for the discharge ﬂoor setting

Add description for the batteries in parallel setting

Reword battery capacity/voltage to Battery bank capacity/voltage.

Orion Smart:

Add ﬁrmware v1.10: (optional update)

Fix charge state report when charger is limited by the input voltage right after starting up.

This caused the charger to report as being disabled in the VictronConnect app, even if it

was already charging the battery. This bug was harmless for the charger, battery, or

loads, only the report was wrong.

2024-09-13 09:45 37/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

BMV & SmartShunt:

Show the ﬁrst use setup only when charged voltage has not been conﬁgured previously. This

avoids the charged voltage to be silently changed when the ﬁrst use setup is completed.

SmartSolar, BMV & SmartShunt:

Mark Bluetooth ﬁrmware v2.41 as mandatory update

v5.72 (Released oﬃcially)

2022-07-25

Changes

SmartLithium:

Add ﬁrmware v1.28: (optional for ﬁrmware v1.24, v1.25 and v1.26, mandatory otherwise)

This ﬁxes the problem found in v1.27. It is strongly advised to install this update when

running ﬁrmware v1.27

v5.71 (Released oﬃcially)

2022-07-18

Changes

Smart Lithium:

Stop further roll out of ﬁrmware v1.27 by putting the ﬁrmware carried in VictronConnect back to

v1.25. Note that any batteries already updated to v1.27 cannot be rolled back. This roll out stop

is due to a bug. See VictronConnect v5.72 for the solution, it adds Smart Lithium ﬁrmware

v1.28, as optional for when battery is running v1.24, v1.25 and v1.26. And mandatory

otherwise.

v5.70 (Released oﬃcially)

2022-07-13

Changes

Support Android 12 new Bluetooth permissions. This allows VictronConnect to scan for nearby

Victron Bluetooth products without having to request location permissions. Only applies to

Android 12 pho

Add Danish & Russian translations

Improve Venus to xlsx converter: Conversion can now cope with partially corrupted VRM log

ﬁles

Several internal improvements

New feature: Sort local products list by name and group user own products. To add a product to

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

the “own” group VictronConnect has to connect to it at least once.

New stored trends feature:

Trends data is kept stored in the product for up to 46 days for most products, except the

Smart Battery Sense, there its 181 days.

SmartSolar, BMV-712 and SmartShunt:

SmartSolar support trends for Batt. Voltage, Current and Temperature, as well as

Load output current, PV voltage and PV current.

BMV-712 and SmartShunt support trends for Battery voltage, Current, State of

Charger % as well as the Aux input (battery temp, or midpoint deviation, or starter

battery voltage).

Interval conﬁguration is equal for above products, and in detail is:

2m at 1s interval (RAM only)

2h at 30s interval

1d at 5m interval

45d at 30m interval

Smart Battery Sense trends:

Support trends for Battery voltage and Battery temperature.

2m at 1s interval (RAM only)

2h at 30s interval

1d at 5m interval

180d at 30m interval

New broadcast data functionality:

VictronConnect can now show the most relevant data of Smart products in the product list

page without having to stablish connection with the product.

Supported by SmartSolar, Smart BMV, SmartShunt, Smart Battery Sense, Lynx Smart

BMS, Smart Lithium and Inverter/Multi/MPPT RS. Firmware versions included in this

VictronConenct release are required.

Broadcast data is disabled by default, can be enabled in product info page.

Broadcast data is encrypted.

Broadcast data has better range than regular connection.

VE.Direct and VRM remote connected devices does also beneﬁt of this new feature; in this

case no new ﬁrmware is needed.

VE.Can products:

Enable VictronConnect-remote for some VE.Can products:

This feature requires Venus OS v2.90 which is not available yet. First v2.90 beta will be

released in Sept 2022 or later.

Enable VE.Can ﬁrmware updates

Supported products:

Lynx Smart BMS

Inverter RS

Multi RS

MPPT RS

Blue/Smart Solar VE.Can MPPTs – Tr and MC4 models

Lynx Shunt VE.Can

Skylla-i

Skylla-IP44/IP65

Unsupported products:

BlueSolar VE.Can MPPT 150/70 - end of life

2024-09-13 09:45 39/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

BlueSolar VE.Can MPPT 150/85 - end of life

Lynx Ion

Lynx Ion + Shunt

Lynx Ion BMS 150A, 400A, 600A, 1000A – Already supported via Bluetooth

Lynx Smart BMS settings:

Improve how the distributors and fuses are presented on screen

Improve the conﬁguration of fuse names including an option to disable unused fuses.

Improve history page

Improve demo mode

Add a button to toggle between On/Oﬀ/Standby modes. This is an improvement to the previous

toggle switch

Reword the hibernate state to oﬀ

Add SOC Synchronize button to the settings menu

Add a setting to manually set the current state-of-charge

Show the date and time for the last 4 errors

Add “Why the device is oﬀ” pop-up. This shows the reason and advices to recover from the oﬀ

state

Add low soc alarm and warning

Add low soc warning and discharge ﬂoor settings

Add ﬁrmware v1.05: (optional update)

Various improvements in On/Oﬀ/Standby handling.

Simplify and improve various automatic protection levels:

For details, see changelog in https://professional.victronenergy.com/

VE.Can MPPT Solar Chargers:

Add ﬁrmware v3.10: (optional update)

Improve overall yield on systems that have ripple over the battery voltage (improvement

done on v3.08)

Fix issue on the GX Device regarding the yesterday history

Support for live data advertisement

Smart Battery Sense:

Add ﬁrmware v1.13 (optional update)

Small trend conﬁguration change (Note: trend data stored using versions <v1.12 will be

erased when updating to v1.12)

Several trend stability ﬁxes

Improved trend download time

Clearing a single trend is not supported anymore (only clearing all trends at once is

supported for now)

Bootloader will be updated to v1.09

SmartSolar, BMV-712 & SmartShunt internal Bluetooth dongle:

Add Bluetooth ﬁrmware v2.41 (optional update)

Support for broadcast data Advertisement

Small trend conﬁguration change (Note: trend data stored using versions <v2.38 will be

erased when updating to v2.38)

Several trend stability ﬁxes

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Improved trend download time

Clearing a single trend is not supported anymore (only clearing all trends at once is

supported for now)

Fixed issue that blocked using the puk while bonding info was still valid

Bootloader will be updated to v1.16

Orion Smart:

Update embedded ﬁrmware from v1.06 to v1.09. Includes various improvements and

enable/disable option for BLE. See change log on Victron Professional for details.

SmartLithium:

Add ﬁrmware v1.27: (optional update)

Support for runtime data advertisement. Disabled by default, to enable it go to Settings →

Product Info and enable “Bluetooth live data advertisement”

Phoenix Smart Charger (120-240V models) :

Add warning 31 (input voltage out of range)

Add option to disable repeated absorption

Add manual recondition button

SmartShunt & BMV-712:

Implement ﬁrst use setup:

Battery capacity and aux input mode needs to be conﬁgure in order to get full access to

settings

Note that this was further improved upon in v5.73: see that change log for details.

Fix current reading has wrong sign when connected via VC-Remote and DC energy meter mode

is enabled

GlobalLink:

Initial support for ﬁrmware v2.06 (not released yet)

Custom name for ve.direct and digial inputs

Read data from Ruuvi sensors

Conﬁgure ruuvi sensors to listen to

Support custommer's simCard

Conﬁgure simCard PIN code and APN

Support read Victron products data via Bluetooth. This feature needs to be supported by

the products via a future ﬁrmware update.

VE.Bus Smart dongle:

Add ﬁrmware v1.12:

Add support for VE.Bus BMS V2 (enables on/oﬀ/charger-only selection in combination with

VE.Bus BMS V2)

Add “External control” status when BOL frames are being detected

Lynx Smart Shunt:

Add initial support

2024-09-13 09:45 41/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Multi RS and Inverter RS:

Add phase L2 & L3 AC values reading (Firmware under development)

Add “Minimum nr of inverters” setting (Firmware under development)

Improve how the NS protection log is registered in the service report

Inverter RS, Multi RS & MPPT RS: Multi RS and Inverter RS:

Add ﬁrmware v1.10:

Reset all protections when using the power switch, remote oﬀ input or device mode oﬀ

command so the device can be restarted remotely.

Repeated absorption interval parameter can now be set to 0 to disable this functionality

as required by some batteries.

Allow fan operation during and immediately after ﬁrmware updates, to prevent a

temperature warning/alarm when updating a unit that is running hot.

Add under-voltage lockout on the DC bus voltage so the internal supply keeps working

under all conditions.

Changes applying to Inverter RS and Multi RS only:

Shutdown the inverter when the connection to the BMS is lost after 3 minutes.

Improve AC coupled PV inverter control mechanism in combination with managed

batteries.

All inverter AC voltages report RMS values.

Improve inverter protection reporting if the cause is an empty battery.

Increase detection time for error Performance enhancements #201, switching on a huge

load could cause a false positive trigger.

Improve inverter dynamic cut-oﬀ behavior by using the actual battery current when

available from a BMS or BMV.

Fix device sleep/wakeup behavior when dynamic cut-oﬀ is enabled or when using the low

SOC shutdown function.

Changes applying to Multi RS only:

Fix charge sequence, charging from the AC input is not possible if the AC input cannot be

used e.g. due to an AUX input rule.

Fix repeated absorption interval behavior in ESS mode, it tries to charge from solar power

ﬁrst, if this is not successful it will charge from the grid after a day.

Speed-up AC input relay open sequence by switching oﬀ both poles of the contactor coil

at the same time.

Add bulk protection mechanism when charging from the grid.

Fix ESS control ﬂag “DisableCharge”.

Fix inverter protections: an active inverter alarm caused the unit to shut-down.

Fix AC incoming solar power on the display when connected to the grid.

Bluetooth interface:

Add support for live data advertisement.

NMEA2000/VE.CAN:

Update PGN 126464 Received and transmit group function content.

v5.61 (Released oﬃcially)

2022-07-01

Download links:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store (Pending of Apple review)

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Please report bugs and give feedback to these betas via the Disqus comments below. Please note that

comments are not public by default, and ﬁrst go to a moderation queue.

Changes

Add ﬁrmware v1.33 for Smart Phoenix Inverter 48V 5000VA: (update mandatory upon

connection)

Reduced maximum fan speed for 48V 5000VA inverters at high battery voltage

v5.60 (Released oﬃcially)

2022-05-25

Changes

VE.Bus Inverter/Charger:

Add MultiPlus and Quattro ﬁrmware v497

v5.59 (Released oﬃcially)

2022-04-04

Changes

RS Inverters and Solar chargers:

Add ﬁrmware v1.09: (optional update)

Changes applying to all RS products (Inverter RS, Multi RS and MPPT RS):

New derating function: the maximum output current is reduced on a linear basis

from full current at 60V to 5A at 62V. Note that this relates to the output voltage at

the battery terminals, and not to the voltage the battery itself, measured with

voltage sense.

The maximum conﬁgurable charge voltage will be reduced from 62V to 60V. The

actual charge voltage can be higher, due to temperature compensation as well as

voltage drop over the cables in combination with Voltage sense. The reason to

reduce the maximum conﬁgurable charge voltage is that specifying it at 62V is

misleading, in combination with the derating. The equalization voltage upper limit is

still 62V.

Fix user relay battery low/high voltage settings range for VictronConnect.

Make over-charge protection error #29 less trigger happy when using external

voltage control.

2024-09-13 09:45 43/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Changes applying to Inverter RS and Multi RS only:

Suppress frequency information when there is no voltage present, on the GX device

you could still see 50Hz or 60Hz while the AC voltage was absent.

Battery over-current error #18 now reports as an overload alarm condition.

Changes applying to Multi RS only:

Prevent battery current overload at low battery voltage when the inverter load

jumps.

Fix Grid disconnect log: conditions causing the inverter to switch oﬀ are now also

logged.

Increase PE-N voltage limit to 42V when using the AC input, the PE-N voltage limit

for the internal relay remains at 8V. The higher PE-N voltage limit is also used

during the relay test sequence. The 42V limit is chosen as this voltage is still

considered to be safe to touch.

Various ﬁxes in ESS modes that are still in beta test stage.

NMEA2000/VE.CAN:

Fix writing/changing the installation description using Unicode characters (PGN

126998).

Fix query acknowledge response code on a write-only register.

Add a setting to disable partial shading detection in MPPT algorithm. This setting must be kept

enabled for optimal performance.

Use equalization voltage upper limit provided by the product.

Orion Smart:

Remove option to disable ﬂoat: Orion Smart doesn't support disabling ﬂoat, doing it will lead to

unexpected behaviour once the absorption stage ends.

BMV & SmartShunt:

Fix remaining time somethimes shows “nanm” value

v5.58 (Released oﬃcially)

2022-03-16

Download links:

Changes

Fix batteries preset temperature compensation setting is always displayed in Celsius even when

Fahrenheit is selected

VE.Bus Inverter/Chargers:

Add new models

MPPT Solar Chargers:

Fix MPPT RS 450/200 max current limit setting

Phoenix Inverter:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Add Phoenix Inverter ﬁrmware update v1.30 for 48V 250VA models (mandatory update upon

connection)

v5.57 (Released oﬃcially)

2022-03-04

Changes

Fix some typos

VE.Bus Inverter/Chargers:

Add new models

SmartLithium:

Fix displayed value and input range for temperature oﬀset setting when using Fahrenheit as

temperature unit.

MPPT Solar Chargers:

Fix some demo models show RX port settings menu while the product doesn't support

alternative RX port functions.

SmartShunt:

Add support for future models

Phoenix Inverter:

Add support for upcoming new models

v5.56 (Released oﬃcially)

2022-02-08

Changes

Android: Fix a bug in Qt framework that makes Android 12 trigger a warning reporting that

VictonConnect pasted clipboard content.

MPPT RS:

Add ﬁrmware v1.08: (optional update)

Fix false-positive error #201 the detection levels were too strict and could be triggered

falsely during MPPT start-up in the morning and MPPT shutdown in the evening.

Fix false-positive error #35 in the MPPT when the irradiance jumps to a higher level (on a

partly cloudy day).

Fix false-positive error #27 in the battery short circuit detection.

Change fan high temperature set-point from 65°C to 57°C.

2024-09-13 09:45 45/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Fix battery state reporting as “external control” in case DVCC current limiting is active.

Make it easier to retry a failed update attempt. VictronConnect will now automatically

prompt to update the unit in case the previous attempt got interrupted.

Inverter RS:

Add ﬁrmware v1.08: (optional update)

Fix false-positive error #201 the detection levels were too strict and could be triggered

falsely during MPPT start-up in the morning and MPPT shutdown in the evening.

Fix false-positive error #35 in the MPPT when the irradiance jumps to a higher level (on a

partly cloudy day).

Fix false-positive error #27 in the battery short circuit detection.

Change fan high temperature set-point from 65°C to 57°C.

Fix battery state reporting as “external control” in case DVCC current limiting is active.

Make it easier to retry a failed update attempt. VictronConnect will now automatically

prompt to update the unit in case the previous attempt got interrupted.

Fix remote discharge current limit behavior in inverter mode.

Multi RS:

Add ﬁrmware v1.08: (optional update)

Fix false-positive error #201 the detection levels were too strict and could be triggered

falsely during MPPT start-up in the morning and MPPT shutdown in the evening.

Fix false-positive error #35 in the MPPT when the irradiance jumps to a higher level (on a

partly cloudy day).

Fix false-positive error #27 in the battery short circuit detection.

Change fan high temperature set-point from 65°C to 57°C.

Fix battery state reporting as “external control” in case DVCC current limiting is active.

Make it easier to retry a failed update attempt. VictronConnect will now automatically

prompt to update the unit in case the previous attempt got interrupted.

Fix remote discharge current limit behavior in inverter mode.

Fix start-up from the ac input without battery (e.g. manually disconnected or contactor

open)

Lynx Smart BMS:

Add ﬁrmware v1.04: (optional update)

Fix in current measurement. Current readings between 80A and 120A could deviate for

certain loads with high peak currents.

Support for Venus OS Lynx Distributor fuse alarms. Distributor alarms are no longer

displayed as error code in Venus OS but displayed as readable alarm messages. This

requires a Venus OS update to v2.81 or higher. Older Venus OS versions will display old

style alarm/error codes.

Support for future Lynx Distributors.

v5.55 (Released oﬃcially)

2022-02-01

Fixes crashes when connecting to a Bluetooth product on macOS.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

v5.55 was released for macOS only, other platforms remain on v5.54.

v5.54 (Released oﬃcially)

2022-01-31

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Please report bugs and give feedback to these betas via the Disqus comments below. Please note that

comments are not public by default, and ﬁrst go to a moderation queue.

Changes

Add support for recently released MultiPlus-II GX and and EasySolar-II GX hardware revision

Known issues

macOS 12.2 aka Monterey: VictronConnect crashes. This issue is expected to be ﬁxed real soon,

ie within days.

macOS 12.2 aka Monterey: VictronConnect is unable to pair to new Victron products via

Bluetooth. Meaning that it is only possible to connect to products that were paired with before

updating the macbook to Monterey. We're working on that, but so far its proving to be a real

challenge. More details in this thread on community.

v5.53 (Released oﬃcially)

2022-01-24

Changes

General:

iOS: VRM login is now done via an in-app web view instead of the default web browser.

Fix issues introducing large numbers when Switzerland locale is selected.

Multi RS:

Add ﬁrmware version v1.07 for Multi RS as a mandatory update.

Add an option to synchronise the battery SOC to 100%

Add Shutdown on SOC setting

Add setting to speﬁfy the source of AC Input

Add setting to enable/disble the motoring of PE to Neutral voltage

Add Aux input settings

2024-09-13 09:45 47/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

SmartSolar, BMV-712 & SmartShunt:

Set Bluetooth ﬁrmware v2.37 as a mandatory update

MPPT RS:

Fix demo product

v5.52 (Released oﬃcially)

2022-01-03

Changes

Improve compatibility with macOS Monterey

Fix application crashes when connecting to a Bluetooth product

Note that Bluetooth pairing is broken in macOS Monterey: connection can only be

stablished with products that were already paired before updating the Apple device to

Monterey. We're working on that, with Apple, but there is no solution on the horizon yet.

Multi RS:

Show AC input in the overview

Lynx Smart BMS:

Fix “Unknown error” is wrongly displayed

Smart Battery Sense:

Add ﬁrmware v1.10 (optional update)

Not possible to connect to Smart Battery Sense anymore is ﬁxed. It ﬁxes the Smart

Battery Sense remaining greyed out in the VictronConnect “Device list” after

disconnecting and not able to be connected anymore, until the device itself was

powercycled (i.e. wires disconnected to force a reset).

Using more accurate timing for storing trend values. This will improve timing accuracy of

the trend graph presented by VictronConnect.

VE.Smart Network settings are also reset when doing “Reset to defaults”

Note: trend data stored using versions <v1.10 will be erased when updating to v1.10

Bootloader will be updated to v1.08

SmartSolar, BMV-712 & SmartShunt:

Add Bluetooth ﬁrmware v2.37 (optional update)

SmartShunt: experimental GATT veregservice extended with support for AUX input vegs

(StarterVoltage, MidpointVoltage&Deviation, Temperature)

Using more accurate timing for storing trend values. This will improve timing accuracy of

the trend graph presented by VictronConnect.

Storing trend data is stopped during an update of attached device (only when updating

via Bluetooth).

Note: trend data stored using versions <v2.37 will be erased when updating to v2.37

Fix for not updating the VE.Smart Network range list. As a result the range list, after initial

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

presentation, would freeze.

SmartSolar: allowing faster switch to new T-Sense source when the currently selected T-

Sense source stops broadcasting in the VE.Smart Network.

Not possible to connect to device anymore is ﬁxed. It ﬁxes the device remaining greyed

out in the VictronConnect “Device list” after disconnecting and not able to be connected

anymore, until the device itself was powercycled (i.e. wires disconnected to force a reset).

Bootloader will be updated to v1.15

Known issues:

Bluetooth pairing is broken in macOS Monterey: connection can only be stablished with

products that were already paired before updating the Apple device to Monterey. We're working

on that, with Apple, but there is no solution on the horizon yet.

v5.51 (Released oﬃcially)

2021-11-23

Changes

Lynx Smart BMS:

Add ﬁrmware v1.03 (Optional update):

A new charging cycle is started when the battery voltages are below 12V/24V/48V (3V per

cell) or when a cell undervoltage is detected. This is in addition to the SoC threshold.

A new charging cycle is started after a ﬁrmware update.

Fixes restore to factory defaults for BLE settings. BLE settings could not be restored in

previous versions.

Fix in pgn127506 not showing consumed Ah's. In previous versions the battery capacity

was shown.

Fix in BMS temperature warning. The GX device did not display a warning at high BMS

temperatures. High temperatures can be the result of dissipation by high currents or a

high ambient temperature that can damage the Lynx Smart BMS.

Removes Load Disconnect message that was displayed in VictronConnect when the unit

was put into hibernate.

Improved high current detection. The high current warning/alarm was not correctly

activated under all conditions. A warning is activated if the current exceeds 600A for

30seconds and an alarm is activated after 5 minutes. Then the loads or chargers are

turned oﬀ depending on the direction of the current.

Chargers and loads will turn back on after 2 minutes.

Activate alarm relay at high current warning and alarm.

Automatic scaling of the charge voltage parameter when the system voltage is changed.

This to prevent a wrong setting of the charge voltage.

Error codes changed #116 for Lost Calibration and #119 for Invalid Settings.

Fix issue where custom device name was not saved properly when the battery was

suddenly disconnected.

BMS cable error detection removed. The detection could give false cable error detections

when more than 1 battery was connected. This could lead to a lock-up because charging

and discharging is not allowed. The detection has been removed because it is impossible

to detect a faulty BMS cable when there is more than one battery connected

2024-09-13 09:45 49/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Phoenix Smart IP43 Charger 120-240V:

Add ﬁrmware 3.50:

Initial ﬁrmware release

v5.50 (Released oﬃcially)

2021-11-17

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

Changes

VE.Bus Inverter/Chargers:

Add ﬁrmware v490:

Add VE.Bus BMS detection and autoconﬁgure mechanism

Add option to remove VE.Bus BMS conﬁguration

Add low battery temperature cut-oﬀ setting for Lithium batteries

Improve the settings write and read progress notiﬁcation

MultiRS:

Add ESS settings menu

Smart Battery Protect:

Fix shut down voltage can be set higher than the restart voltage in demo product.

v5.49 (Released oﬃcially)

2021-10-29

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

Changes

VE.Bus Inverter/Chargers:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Increase conﬁg level to enable settings on new ﬁrmware v489 (ﬁrmware not included)

v5.48 (Released oﬃcially)

2021-10-07

Changes

Fix demo products show “This is latest version!” although version number is not shown

Hide status in the VE.Smart networking page during the setup process, it can be confusing.

Fix crash when a GX device on local lan is detected multiple times. This can happen when a GX

device is connected to LAN via ethernet and Wi-Fi simultaniously.

Blue Smart Charger:

Add ﬁrmware v3.42 for Blue Smart IP22 Chargers REV2 (Optional update):

Only for models with production date week 24 of 2020 (serial number HQ2024nnnnn and

newer).

Fix temperature cut-oﬀ not always working; issue introduced in v3.40

Fix discrepancy between charge cycle history state time and the actual time

Add ﬁrmware v3.41 for BSC IP65XS 6/12V:

Remove low temperature battery settings as it doesn't apply to the BSC IP65XS

6/12V-1.1A model

BMV-712 & SmartShunt:

Add ﬁrmware v4.08 (optional update)

For non-bmv monitor modes the current and power are inverted to match installation and

visual feedback. A positive current is deﬁned as current ﬂowing outward from a source

and inward into a load.

For non-bmv monitor modes the bmv charging history items are disabled and kWhOut

and kWhIn are renamed to EnergyOut and EnergyIn.

Water Heater is added as a (load) option for Monitor Mode.

Show GATT switch only when connected via Bluetooth

Mark GATT as experimental feature

Fix “Altenator” typo

VE.Can MPPT Solar Chargers:

Add ﬁrmware v3.07: (optional update)

Fix bug when using the internal temperature to estimate ambient temperature. Now

ambient temperature estimation saturates on 49C.

Fix bug of disabling temperature compensation when battery temperature was above

50C.

MPPT Solar Chargers:

Add ﬁrmware v1.59: (optional update)

Fix bug introduced on v1.58 that caused the MPPT to reduce yield when PV array is close

to and battery voltage.

Fix bug when using the internal temperature to estimate ambient temperature. Now

2024-09-13 09:45 51/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

ambient temperature estimation saturates on 49C.

Fix bug of disabling temperature compensation when battery temperature was above

50C.

Apply same PV Short Protection improvements (errors 38 and 39) already used on the

250V models (safety improvement - introduced on v1.58).

Reduce maximum charger output voltage to 65V (introduced on v1.58).

Add error 40 to detect when PV short functionality does not work (safety improvement -

introduced on v1.58).

Fix some demo models do not show StreetLight settings menu

MPPT RS:

Add ﬁrmware v1.05: (optional update)

Add TEXT protocol on the ve.direct interface (Inverter RS).

Add internal DC voltage measurement safeguard. In case the measurement is not ok the

unit stops working, showing error code 201. This prevents over-charging a battery or

damage to the internal circuitry.

Fix MPPT start-up sequence: bench testing the MPPT using a power supply could damage

the internal circuitry (using ﬁrmware v1.04).

Fix 30-day MPPT history readout.

Fix bug when disabling temperature compensation. It was not fully disabled when battery

temperature was above 50°C.

Fix bug for DVCC’s limit charge current when having only one charger connected on the

VE.CAN bus.

Improve control loop stability of the built-in MPPT.

Add DC input resistance readout

Rename imput mode from BMS to 2-Wire BMS

Do not not warn about remote mode not in set to 2-Wire BMS when selecting Lithium. A VE.Can

BMS can be used instead.

Do not automatically switch remote imput mode to 2-Wire BMS when Lithium preset is selected

from VictronConnect presets library. Remote mode will change if the MPPT built-in “Lithium 2-

Wire BMS” is selected.

Inverter RS:

Add ﬁrmware v1.05: (optional update)

Add TEXT protocol on the ve.direct interface (Inverter RS).

Add internal DC voltage measurement safeguard. In case the measurement is not ok the

unit stops working, showing error code 201. This prevents over-charging a battery or

damage to the internal circuitry.

Fix MPPT start-up sequence: bench testing the MPPT using a power supply could damage

the internal circuitry (using ﬁrmware v1.04).

Fix 30-day MPPT history readout.

Fix bug when disabling temperature compensation. It was not fully disabled when battery

temperature was above 50°C.

Fix bug for DVCC’s limit charge current when having only one charger connected on the

VE.CAN bus.

Improve control loop stability of the built-in MPPT.

Fix internal charger group id (PIN482600000 Inverter RS without built-in MPPT).

Add DC ripple voltage readout

MPPT Control:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Add ﬁrmware v1.03 (mandatory update upon connection)

Solve MPPT Control getting stuck in “CONNECTING”

Make the communication more robust

Add support for new MPPTs

Fix that when autolock is set to false, it would still lock 1 more time.

Fix display of MPPT software version

VE.Bus Inverter/Charger:

Add ﬁrmware v487

v5.47 (Released oﬃcially)

2021-08-13

Changes

MPPT Solar Chargers:

Fix temperature cut-oﬀ keeps showing as enabled after toggling the disable switch.

Temperature cut-oﬀ is disabled by default. Bug was introduced in v5.46 two weeks ago, and is

only noticeable when enabling the cut-oﬀ(disabled by default) and then trying to disable it

again.

v5.46 (Released oﬃcially)

2021-07-29

Changes

Add support for BlueSolar MPPT VE.Can 150/100 Rev2

v5.45 (Released oﬃcially)

2021-07-19

Changes

Fix GX products LAN/WiFi discovery on iOS and improve it on rest of platforms

Lynx Smart BMS:

Add ﬁrmware v1.02: (mandatory update upon connection)

Improve control for alternators, by (1) ensuring that the delay between opening the ATC

contact, and subsequently opening the main contactor (i.e. disconnecting the batteries

from the system) is at least 2 seconds in all situations. And (b) adding an “Alternator ATC

control” mode for the programmable relay. With that addition, it has two modes: Alarm

(default) and Alternator ATC control. For systems with alternators, set this mode and wire

the alternator control to the user relay. Do not use the normal ATC contact for controlling

2024-09-13 09:45 53/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

an alternator. The advantage of this special mode is that it will only engage the alternator

when the battery bank is connected to the system.

Added contactor, user relay and ATC/ATD status to NMEA2000 switch bank status PGN.

A low battery warning is given 30s before a not-allowed-to-charge signal for batteries that

do not support pre-alarm.

Improved CVL control. In case of an overvoltage, CVL quickly forces the chargers oﬀ by

lowering the charging voltage. Then, the voltage is slowly increased to the battery

voltage.

Added ATC/ATD-failure error. This error occurs if the BMS has to open the contactor

because ATC/ATD cannot reduce the charge/discharge currents. By naming that ATC/ATD-

failure, it is more clear to the user that there is a problem in the wiring of his system.

The wording “Pre-alarm” is replaced by “Low cell voltage warning”.

Loads remain on for 30s after disconnecting the M8 BMS cable. A new “BMS cable alarm”

together with a “load will disconnect warning” is added to warn the user that the system

will shut down after 30 seconds in case the cable is not reconnected in time.

Added an emergency power-up feature, to start the Lynx Smart BMS after it has shut

itself down in hibernate. What is hibernate? It’s a shutdown mode that limits permanent

damage to the batteries as much as it can. In more detail, the LSB will shut itself down

into hibernate when it measures an extremely low battery voltage (V < 10V, meaning <

2.5V per cell). ATC contact is opened (since keeping it closed draws current from the

battery), Aux port and thus GX devices are shutdown and so forth, which also prevents

any chargers from charging again. In the old situation, the only way to get out of that was

by adding an external charger, i.e. one not controlled via ATC, and charging the battery to

over 12.8V (= 3.2V per cell). Now, this new feature allows a restart via the remote on/oﬀ

input: once in hibernate, the LSB can be restarted by switching the device oﬀ for 5

seconds with the remote and then on again.

Fix in SoC calculation. This solves the problem where SoC could go to 0% while the

battery was fully charged; in some cases this caused a longer absorption time (CVL =

14.2V) than necessary.

Added CAN support for Wakespeed WS500 controller.

Instead of only lowering the CVL, now also CCL is set to 0A if charging is not allowed (cell

overvoltage or low cell temp). Together with Venus OS v2.72, this improves operation in

ESS.

Several internal improvements.

VE.Bus Smart Dongle:

Add ﬁrmware to v1.11: (mandatory update upon connection)

Fixed constant connection reset bug, introduced in V1.10, between dongle and inverter on

MultiPlus/Quattro ﬁrmware versions before xxxx460

Fixed MultiPlus/Quattro status brieﬂy indicated FAULT immediately after ﬁrmware update

or power cycle

Add dongle status feedback during initialization and mode switch between secondary and

primary mode.

SmartLithium:

Add ﬁrmware v1.25 (optional update)

VE.Bus Inverter/Chargers:

Add ﬁrmware v485 (optional update)

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

MultiPlus-II GX:

Show the proper icon in the devices list when listing the GX part of the product.

BMV-712 & SmartShunt:

Show power instead of voltage in main widget when conﬁgured as DC monitor

v5.44 (Released oﬃcially)

2021-07-01

Changes

VE.Bus Smart Dongle:

Rollback ﬁrmware to v1.09: (mandatory update upon connection)

Firmware v1.10 included in previous VictronConnect release has an issue that constatly

resets the connection between the dongle and the inverter. This issue is only present

when the MultiPlus or Quattro is running a relatively old ﬁrmware version.

VE.Bus Inverter/Charger (connected with MK3-USB):

Fix connection/disconnection loop, This issue is only present when the MultiPlus or Quattro is

running a relatively old ﬁrmware version.

v5.43 (Released oﬃcially)

2021-06-24

Fixes landscape layout on Android tablets.

v5.43 was released for Android only, other platforms remain on v5.42.

v5.42 (Released oﬃcially)

2021-06-23

Changes

Various internal VRM improvements

Add Turkish language

Improve translations

Stop animations while not visible. This has an impact on Inverter RS ﬁrmware updating time on

Windows which is now improved.

Open links to manuals in VC selected language whenever available.

Fix an issue on Android phones that makes that the toolbar is not properly drawn on Android

phones. This issue is caused because Android provides wrong display metrics. So far, this issue

has only been observer on phones with a 21:9 aspect ratio screen.

2024-09-13 09:45 55/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Fix some Android system conﬁguration changes can make VictronConnect crash and show a

white screen.

Blue Smart Charger:

Add ﬁrmware for future IP65 6V/12V model (mandatory installation upon connection):

First oﬃcial release

Add re-bulk method setting (IP22 REV2 only)

Allow full current range on IP22 REV2 models (IP22 REV2 only)

Fixed demo mode for build-in battery types

Added explanation to recondition voltage setting

Fix bulk time unit in CSV history export

Add ﬁrmware v3.40 for rev2 models: (Optional update)

Update for Blue Smart IP22 Chargers REV2 only; starting production date week 24 of 2020

(serial number HQ2024nnnnn and newer). The hardware revision printed on the the

product label should be “hw rev 02” or higher.

Support for VE.Smart networking

Blink status LEDs brieﬂy once every 4 seconds to indicate VE.Smart networking is

active

Added support for synchronized charging, allowing to parallel multiple chargers and

synchronize their charge algorithms. Compatible with SmartSolar chargers, where

the Blue Smart charger will become the charge master.

The PV power of all solar chargers is totalized by the charge master and

broadcasted into the network to be displayed in VictronConnect when

connected to a solar charger.

The battery idle voltage at sunrise, needed for aborption time calculation, is

taken from the solar charge master upon master take-over. This value is

continued to be broadcasted into the network for the solar chargers, to be

able to continue charging if the Blue Smart Chargers are disconnected from

the network.

Manual equalisation from the solar charger settings menu in VictronConnect

will be delegated to all devices in the network by the charge master.

Enforce re-bulk voltage method, to prevent premature re-bulking when only

the charge master is providing the full current. This setting is only enforced

when the charge master has detected other chargers in the network and will

continue to use the user selected method is case of stand-alone mode. The

enforced setting is volatile, meaning that when the charger is restarted it will

revert back to the last value the user has selected.

Added support for VSense; to be used for cable loss compsensation for individual

network nodes

Added support for TSense; to be used for temperature compensation and low

battery temperature cut*oﬀ, required for lithium batteries.

Added support for ICharge; when available, the total charge current of all chargers

on the network will be used for the tail current.

Added support for ISense; when available, the battery current will be used for the

tail current. This value is prioritized over the ICharge value. Requires a BMV or

SmartShunt.

VE.Smart networking settings will be reset upon a “Reset to defaults” in

VictronConnect.

Added low battery temperature cut-oﬀ

Requires VE.Smart networking temperature sensor, e.g. Smart Battery Sense or

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

SmartShunt

When pressing the `Why is my charger oﬀ?` button in VictronConnect it will state

that the charger is oﬀ due to a low battery temperature.

Because the charger cannot be totally switched oﬀ, the setpoints are set to lowest

value possible, i.e. 12.8V and 25% * Inominal for a 12V unit.

Note for Victron Smart Lithium batteries, above feature is not relevant. Since then

the BMS will disable the charge when the batteries are below 5°C, and also in case

of cell over voltage. More clearly: its not necessary to buy a Smart Battery Sense to

make sure a Phoenix Smart Charger stops charging a Victron Smart Lithium Battery

below 5°C.

Add tail current functionality

When the charge current is below the threshold for 1 minute, the absorption stage

is ended and the charger will switch to ﬂoat/storage.

Add re-bulk method based on voltage; this method can be selected using the “Re-bulk

method” setting in VictronConnect

When the charge current is below the threshold for 1 minute, the absorption stage

is ended and the charger will switch to ﬂoat/storage. Note that the re-bulk current

setting is ignored when this method is selected.

The default re-bulk behavior remains unchanged, to be able to use the product as

mobile charger.

Allow 0% recondition current

This ﬁxes an issue with the VictronConnect lithium preset

Setting it to 0% skips the recondition stage, if enabled

The charge current is now adjustable over the full range, from 25*100% * Inominal

The recondition current is now conﬁgurable from 0-50% (0=disabled)

Improved temperature compensation

Compensate down to -20°C for bulk and absorption, instead of only 6°C. During

ﬂoat and storage, the compensation is only down to 6°C, as per best practises: to

charge a very cold battery, increase the charge voltage; but not to “ﬂoat” a battery.

With this change the temperature compensation works the same as our Solar

Chargers as well as Multi and Quattro inverter/chargers.

Add hardware check for internal temperature sensor

In case malfunction, the temperature derating and compensation works incorrectly

An error 23 will be issued in case of sensor malfunction; this is not auto-recoverable

and requires a power cycle of the unit. If the error persists, the unit is broken.

Allow absorption time less than 1 hour (community request)

When adaptive charging is selected, the minimum absorption time of 30 minute is

still honored. When a ﬁxed absorption time is selected, it is possible to disable the

entire absorption stage.

Improve bluetooth connectability with VictronConnect

Show hardware revision for IP22 demo products:

Rev2 models have diﬀerent capabilities than the Rev1 ones and thus diﬀerent settings

Phoenix Smart Charger:

Move charger on/oﬀ switch onle level up to the main settings page

Add ﬁrmware v3.38: (Optional update)

Update for Phoenix Smart IP43 Chargers Rev1 24/16 (1+1) and 24/16 (3) only

Increase minimum charge current from 10% to 25% due to hardware restrictions

Fixed issue that charge current can get stuck at ~1.5A; regression introduced in

v3.31

2024-09-13 09:45 57/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

SmartLithium:

Add ﬁrmware v1.24: (mandatory installation upon connection)

Balancer status indicator showing the state of imbalance between the cells in

VictronConnect. It shows the current balancer status and indicates whether it is necessary

to rebalance the cells.

Added a counter to show the time since last full charge.

Support for reset command so a user can manually reset the controller in case of issues

as it is not possible for a user to power cycle the battery.

Time since last full balancing indicator. This indicates the time since the battery was fully

charged and balanced. It is recommended to fully charge the battery at least once a

month.

Extension of charger disconnect depending on peak cell voltage. This to give the balancer

more time to balance the high cell before charging is turned on again. In some systems,

there is a delay between the charger disconnect signal and the actual stopping of the

charger. This may cause higher cell voltages and can get worse when the charger is

turned back on too soon, resulting in a new overvoltage alarm. Therefore a delay of 1-20

minutes is added depending on the peak cell voltage. During this delay, the balancing

process continues. This reduces the number of overvoltage alarms and protects the cells

against excessive high voltages.

VE.Bus Inverter/Chargers:

Add support for MultiPlus-II 2x120V split phase models

Show L2 information for MultiPlus-II 2x120V split phase models

Fix values can freeze when swithing between apps while connected to a Multi. (Android only)

Add latest ﬁrmware v482, v484 for MultiPlus-II 2x120V:

Changes to comply to new French and Austrian grid codes.

Improved BF failure detection mechanism.

VE.Bus Smart Dongle

Add ﬁrmware v1.10: (mandatory installation upon connection)

Fix switchover is sometimes shown in secondary mode

Add support for MultiPlus-II 2x120V split phase models

Bootloader: Always reset bootloader after every update attempt

Limit low cell voltage prealarm minimum value to 2.85V. Firmware doesn't allow setting lowe

values.

Solar Chargers:

Add ﬁrmware v1.57 for BlueSolar & SmartSolar 100-50 models:(mandatory installation upon

connection)

Fix issue that could occur on some units that leads to a wrong measurement of all analog

signals (i.e. measuring higher battery voltage than real) after a cold start (restart after

battery and PV were disconnected from the charger).

Multi RS Solar:

Add initial support

Inverter RS & MPPT RS:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Add support for Inverter RS models without MPPT

Rename Li-ion built-in preset to LiFePO4 2-wire BMS

Add ﬁrmware v1.04:

Features:

Further increase operational temperature range so the unit can be used up to 65°C

ambient temperature.

Derate the MPPT charge power if needed to keep the inverter operational at higher

temperatures (Inverter RS).

Add support for discharge current and voltage limit to remotely switch oﬀ the

inverter, this enables future integration with managed batteries using a Venus GX

device (Inverter RS).

Panel isolation / residual current detection issues only stops the inverter, the

inverter restarts automatically once these issues are resolved.

Add internal energy counters for data logging to our VRM site (Inverter RS).

Change/Reset the pincode for the Bluetooth connection is now supported over a

wired connection.

Bugﬁxes:

Fix error 35 (over-power): Speed-up MPPT voltage control to avoid a battery voltage

overshoot in case the battery is disconnected during charging or PV power jump

while the unit is charging.

Fix error 27 (short circuit): Improve start-up at low battery voltages e.g. when a

contactor connects the battery.

Fix start-up on shorted battery terminals to make the unit short-circuit proof.

Fix internal supply start-up (applies to Inverter RS units produced before 2020 week

30).

Fix error 14 (battery temperature low) and error 120 (voltage reference) when

disconnecting the battery.

Make the over-voltage protection less trigger happy, also do not report error 53

(inverter internal dc voltage too low) if this protection is activated.

Residual panel current detection implementation updated according NEN-IEC

62109-2:2011, the previous implementation was stricter than required.

Fix user relay setting on the MPPT RS models.

Fix 30-day history on systems that only use an external AC coupled PV inverter.

BMS missing condition uses a voltage set-point based on the battery settings

(ﬂoat/storage).

Disable internal state-of-charge mechanism in case it is managed externally.

Disable voltage alarms on the GX Device (MPPT RS)

Phoenix Inverter:

Add ﬁrmware v1.27 for some 120V models (optional update):

User controlled ACout voltage is reduced to 100V, was 110V. (For recent produced

models)

Add ﬁrmware v1.25 for Smart Phoenix Inverters 1600/2000/3000VA - 230Vac: (Optional update)

Reduced power when AC output is oﬀ and device is in hibernation mode

Fix for saved history data issue

Add ﬁrmware v1.24 for new 800-1200VA 230V VE.Direct Inverters models: (Optional update)

Improved small load detection in Eco mode

Fix for saved history data issue

2024-09-13 09:45 59/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Lynx Smart BMS:

Add ﬁrmware v1.01 (mandatory installation upon connection):

Improved battery monitor calculations. This also solves the problem where the SoC

counter suddenly stops at very low currents with large battery banks.

Fixes the issue where CVL is always set to storage voltage in 24V and 48V systems.

Fixes the issue where BLE could not be enabled with GX devices.

Contactor status added to display the switch status correctly in GX devices.

Number of parallel battery strings setting added for better behavior of the balancing

program with parallel connected batteries.

* Add number of parallel batteries setting * Correct some of displayed error numbers

BMV-712 & SmartShunt:

Add ﬁrmware v4.07 (optional installation):

Added monitor mode. Setting can be conﬁgured via settings menu (item 72 in BMV) or via

VictronConnect. When a non-bmv mode is selected all charging related functionality will

be disabled (consumed energy, SOC, charged cycles etc) and this also applies for the

history items.

Changed default current threshold for SmartShunt 1000A/50mV and 2000A/50mV to

200mA and 400mA respectively (applicable when restoring to default).

Add Bluetooth ﬁrmware v2.30 for SmartBMV/SmartShunt (mandatory installation upon

connection):

VE.Smart Networking disabled during update of device. This ﬁxes the error message that

the update failed (the update itself was successful but the veriﬁcation could not be

accomplished, hence the error message).

Add monitor mode setting available in Misc settings page.

Limit low SOC relay clear setting to a max value of 99%, 100% is not allowed by ﬁrmware.

Fix low SOC relay setting range slider is partially hidden when Dutch and French languages are

selected.

v5.41 (Released oﬃcially)

2021-04-26

Changes

SmartShunt & BMV battery monitors:

Fix zero current calibration data is copied across settings ﬁles. This prevents copying incorrect

calibration data to other units, for example when using a master setting ﬁle to batch conﬁgure

multiple units.

Improve the warning text shown when triggering a zero current calibration

GlobaLink 520:

Show an informative warning when connection from an Android phone.

Smart Battery Sense:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Update product icon to the latest design

v5.40 (Released oﬃcially)

2021-04-20

Changes

* Fix SmartLithium and Orion Smart demo products doesn't open.

MPPT Solar Chargers:

Add ﬁrmware v1.56: (optional, mandatory installation only for some 150/35 & 150/45 models)

Improve battery life algorithm by not allowing the voltage oﬀset to decrease too fast to

zero during a cloudy day.

Change total input power data handling to allow report when charger is oﬀ.

Improve ﬁxing load output introduced on v1.54. There were still some rare cases that the

load output could brieﬂy turn oﬀ. This latest version should ﬁx that.

Fix overcurrent fast software detection on the SmartSolar 150/35. That caused the

charger to get “stuck” on a low power output which was only reset when the charger

stopped charging.

VE.Bus Inverter/Charger:

Add new models to the products database.

v5.39 (Released oﬃcially)

2021-04-12

Smart Battery Protect:

Add ﬁrmware v2.08 (mandatory installation upon connection)

Added PROG option for PIN reset (‘P’)

Disabled SBP will now try to pull output voltage to 0V

Thus providing reliable Phoenix Inverter REMOTE disconnect

Several internal improvements

Warn that load output is disabled for a short period of time during the ﬁrmware update

Smart BMS 12/200:

Add support for the new Smart BMS

Add ﬁrmware v1.06 (mandatory installation upon connection)

Fix fuse type is not selected warning is shown while in the ﬁrmware update page

Smart BMS CL 12-100:

Add ﬁrmware v1.06 (mandatory installation upon connection)

Fix fuse type is not selected warning is shown while in the ﬁrmware update page

Blue Smart Charger:

2024-09-13 09:45 61/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Add ﬁrmware v3.25 for some of the IP22, IP65 & IP67 models (mandatory installation upon

connection)

Add support for future models

IMPULSE-II:

Add ﬁrmware v3.26 & v3.36 for some models (mandatory installation upon connection)

v5.38 (Released oﬃcially)

2021-02-10

Changes:

Fix an issue on Android 11 that can break the scan button and make the devices list show

empty when VictronConnect has been in background for a while.

Update links to manuals

VE.Bus Inverter/Charger:

Include ﬁrmware v481

VE.Bus Smart Dongle:

Add ﬁrmware v1.09:

Fixed SOC 100 percent while battery monitor disabled bug (mandatory installation upon

connection)

Add mode switch to overview page

Hide input current limit button when the inverter/charger is oﬀ

SmartLithium:

Add ﬁrmware v1.20:

Improved recovery mechanism to prevent balancer hangup when an internal error occurs.

Inverter RS:

Fix frequency unit

v5.37 (Released oﬃcially)

2021-02-02

Fixes Bluetooth issue on Android. v5.37 was released for Android only, other platforms remain on

v5.36.

Note that a Google SDK update forced us to change the required type of location permissions to

“ﬁne”. As explained in the manual, and in response to various feedback, we are not happy about this

at all - its a result of how Google and Android works in combination with Bluetooth Low Energy. Note

that VictronConnect is not sending any data to Victron, and for sure its not sending any location data.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

v5.36 (Released oﬃcially)

2021-02-02

Changes:

General:

Added continuous BLE scan: instead of only scanning once when opening VictronConnect, and

thereafter only when the scan button was pressed, it will now keep scanning as long as the

Device list page is open. Products will appear in the list as soon as they are in range. A note on

power consumption and this change: Continuous scanning has no impact on the power

consumption of the Victron product. For phones, tablets and laptops, it will of course will have

an impact on battery consumption, but that will be rather minimal if even measurable at all. The

continuous scan is only active when the app is in the foreground and on the devices list page.

When the app is sent to the background or connected to a product, the scanning stops. The

refresh buttons remains, pushing it will make VictronConnect scan for VE.Direct devices, refresh

the VRM installations list, and restart the Bluetooth scanning just in case it is needed.

Added Bluetooth signal strength indicator to the Device list page.

Increase Bluetooth connection timeout. Prevents the retry mechanism to be triggered too early

in some old devices.

Fix custom name length limit when pasting non-ASCII texts

Show badge on top of the settings icon when a ﬁrmware update is available

iOS: Fix Google Drive and probably other apps doesn't show the option to open ﬁrmware ﬁles

with VictronConnect

Fix crash reported when closing VictronConnect on macOS Big Sur and iOS 14

Fix crashes on iOS when bringing back the app from background

Added the Lynx Smart BMS to the demo list (note that this product is not available for sale yet)

VE.Bus inverter/charger:

Include ﬁrmware v478

Add VE.Bus system conﬁguration:

Guided Parallel, three phase and split phase systems setup

Guided standalone mode reset when only one unit is detected

Max of three units can be conﬁgured, for larger systems, use VE.Bus System Conﬁgurator.

Detects outdated ﬁrmware and version mismatch between units and oﬀers the option to

update them during the guided setup when setting up a new system.

AC switch over info:

Show the reason why the grid is rejected

Once grid is available again, the remaining time for AC input activation is shown

Show when AC input is ignored

Add detection of wrong phase rotation on AC in

Fix absorption time and interval can't be modiﬁed in demos

Inverter RS & MPPT RS:

Add ﬁrmware v1.03 (optional install):

Add option in VictronConnect to set the battery state-of-charge to 100% (Inverter RS)

Show a warning (#14) on the display if a LiFePO4 battery is not charged due to low

temperature

2024-09-13 09:45 63/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Show a hint on the display why the unit does not start (no PV power, remote input oﬀ,

etc.)

Turn oﬀ the display backlight if there is no PV power (MPPT RS), this behavior can be

changed in VictronConnect

Add PV isolation resistance measurement, shut down below 100kΩ (MPPT RS)

Update operational temperature range so the unit can be used up to 60°C ambient

temperature

Improve ﬁrmware update mechanism

Fix issue that caused a loop “Fetching data…” and “Reconnect” when connecting to a unit

using Bluetooth

Fix battery low/high warnings during standby/oﬀ

Fix battery current readout during standby

Fix history data: the previous ﬁrmware can lose data when restarting/updating ﬁrmware

Clear history data no longer resets the battery state-of-charge

Improve internal power distribution over multiple trackers (MPPT RS)

Clear manual equalization active when a re-bulk event occurs

Low battery/overload conditions are no longer reported as errors as these are normal

operating conditions

Shutdown communication interfaces when the power switch is in the oﬀ position

Inverter RS:

Add inverter ground relay enable/disable setting

Add AC frequency readout

Add ”#14 battery temperature too low“ error

Warn about 8:1 ratio when setting ﬂoat voltage, including the calculation of max PV voltage for

the given ﬂoat voltage value

MPPT RS:

Warn about 8:1 ratio when setting ﬂoat voltage, including the calculation of max PV voltage for

the given ﬂoat voltage value

Add ”#14 battery temperature too low“ error

VRM:

Add installation ﬁltering by tag

Fix VRM login on Android 5 phones, this issue was present since ﬁrst release of the VRM

functionality

Cerbo GX:

Fix Bluetooth connection process can get stuck

Smart Battery Protect:

Add ﬁrmware v2.05 (optional install):

Improved Bluetooth disconnect behavior

Fixed spurious error E6 (Reference voltage failure)

Several internal improvements

BMV & SmartShunt:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Add BMV-710H, BMV-712 and SmartShunt ﬁrmware v4.05 update (optional install):

Changed minimum accepted temperature for alarm/relay to -40 Celcius (was -99 Celcius).

Fix: Relay/Alarm temperature settings below -17 Celsius accepted.

Limit max measured temperature to 100 Celsius.

Fix: disable buzzer before entering bootloader/update mode. This will prevent a

continuing high pitch beep during the update when the buzzer was active while starting

the update. (BMV only)

Leave auto cycle status mode by pressing minus button for 3 seconds (same as entering

auto cycle status mode). While auto cycle status is enabled: (BMV only)

Pressing any button shortly will only enable the LCD backlight.

Pressing plus or minus shortly will show the previous/next status item.

Pressing setup button for 2 seconds will enable settings menu.

Pressing setup and select button simultaneously for 2 seconds will restore default.

Fix: enabling auto cycle status when not releasing button right after beep. Keeping minus

button pressed when enabling auto cycle status mode, will not cancel the auto cycle

status mode anymore. (BMV only)

Added “None” option to auxiliary input conﬁguration. The “None” option is the default

conﬁguration. Settings 22-31, 39-48, 58-60, 67-68 are disabled in the settings menu

(display) when the the aux input is conﬁgured to “None”.

Fix: wrong relay activation due to using uninitialized voltage measurement at startup.

Add BMV-70x ﬁrmware v3.11 update (optional install):

Changed minimum accepted temperature for alarm/relay to -40 Celcius (was -99 Celcius)

Added “None” option to auxiliary input conﬁguration. The “None” option is the default

conﬁguration. Settings 22-31, 39-48, 58-60, 67-68 are disabled in the settings menu

(display) when the the aux input is conﬁgured to “None”.

Fix: wrong relay activation due to using uninitialized voltage measurement at startup.

Orion Smart:

Update demo products to make use the same engine shutdown detection settings introduced in

latest ﬁrmware version

IMPULSE-II:

Add support IMPULSE-II 24/8 Smart IP44 model using new microprocessor

Add ﬁrmware v3.23 update for IMPULSE-II 24/8 Smart IP44 (optional install)

Same as v3.17, but adds support for IMPULSE-II 24/8 Smart IP44 model using new

microprocessor

SmartBMS CL:

Add ﬁrmware v1.03 update (optional install):

Improved Bluetooth disconnect behavior

Fixed spurious error E-B33 (Reference voltage failure)

Several internal improvements

Various UI improvements

Avoid duplicated alarms

BlueSolar & SmartSolar MPPT:

Fix PV section shows duplicated when connected through VRM

Add missing Streetlight settings menu in BlueSolar 100/20 demo

2024-09-13 09:45 65/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

VE.Bus Smart Dongle:

Add ﬁrmware v1.08 update (mandatory installation upon connection):

Changing the AC input current limit is now possible for systems that have a VE.Bus BMS.

Requires VE.Bus ﬁrmware 415 or newer on the inverter/charger. The other limitation,

switching between On/Oﬀ and Charger-only is unfortunately still not possible for systems

that have a VE.Bus BMS.

Add ignore AC input status

Add default PIN code detection

Add detection of wrong phase rotation on AC in

Add support for back feed relay switchover status readout

Fixed AC input current limit temporarily reports wrong value during AC input switch over

Bluetooth related changes:

Added VE.Smart networking functionality (sharing battery voltage and temperature

sense with for example an Solar Charger)

Report when product is connectable or not

Improved clearing bond info on pincode change

Improved disconnection behaviour

v5.35 (Released oﬃcially)

2020-11-04

Changes

Fix freeze on Windows at startup and/or when scanning

Improve VRM connection by retrying to connect before showing a timeout error.

Fix VRM sign in button doesn't open the browser on iOS 14 when Safari is not the default

browser. This issue also aﬀects other links in VictronConnect.

Add support for the upcoming Lynx Smart BMS

Improve Venus backlog to xlsx converter:

Speed up conversion time by a factor of ~5

Remove maximum 500MB sqlite3 backlog ﬁle size

Show conversion progress

Add cancel button

MPPT Solar Chargers:

Add ﬁrmware v1.54 (non-mandatory):

Fix load output brieﬂy turning oﬀ when charger is enters low power mode, introduced on

v1.52 on SmartSolars.

Improve error 38 detection for SmartSolars 250/60 and 250/70 models.

VE.Bus Inverter/Chargers:

Enable high speed communications: Shortens the time needed for retrieve values and settings.

Increase the Multi/Quattro detection timeout when scanning.

Smart Chargers:

Fix CSV export: starting at second column, values are shifted left by one column.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Smart Battery Protect:

Fix sometimes error/alarms notiﬁcations are not cleared

BMS-CL:

Fix sometimes error/alarms notiﬁcations are not cleared

Inverter RS:

Fix charge voltage limits on demo products

MPPT RS:

Fix charge voltage limits on demo products

v5.34 (Released oﬃcially)

2020-10-21

Changes

Sort VRM installations by name

Add timeout when connecting to a Bluetooth product to prevent connection getting stuck and

ensure that the retry mechanism is triggered.

Fix some texts do not update when switching language until the application is restarted

Improve VE.Smart networking on demo products

Phoenix Smart Charger:

Add ﬁrmware v3.31 update:

Add support for VE.Smart networking

For now only Vsense and Tsense. Synchronized charging is scheduled for a future

release

Blink status LEDs brieﬂy once every 4 seconds to indicate VE.Smart networking is

active

Add history of the last 40 charge cycles, similar as the Blue Smart Chargers

Note that the history is the total of all outputs

Use re-bulk voltage oﬀset instead of absolute re-bulk voltage

The re-bulk voltage is migrated to re-bulk voltage oﬀset based on the lowest

setpoint

Improved temperature compensation

Compensate down to -20°C for bulk and absorption, instead of only 6°C. During

ﬂoat and storage, the compensation is only down to 6°C, as per best practises: to

charge a very cold battery, increase the charge voltage; but not to “ﬂoat” a battery.

With this change the Phoenix Smart Charger temperature compensation works the

same as our Solar Chargers as well as Multi and Quattro inverter/chargers.

Lower the minimum conﬁgurable charger current from 25% to 10% * Inominal

Add low battery temperature cut-oﬀ: stop charging lithium batteries below 5°C (default)

Requires VE.Smart networking temperature sensor, e.g. Smart Battery Sense

When pressing the Why is my charger oﬀ? button in VictronConnect it will state that

the charger is oﬀ due to a low battery temperature.

2024-09-13 09:45 67/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

For the current hardware (Rev1), instead of switching the unit oﬀ the setpoints are

set to lowest value possible, i.e. 12V and 10% * Inominal for a 12V unit. This for the

reason that it cannot be guaranteed that a battery voltage is always present, which

is required for the charger to switch oﬀ. Some lithium batteries with build-in BMS

will cut themselves oﬀ in case of over/under voltage or temperature.

Note for Victron Smart Lithium batteries, above feature is not relevant. Since then

the BMS will disable the charge when the batteries are below 5°C, and also in case

of cell over voltage. More clearly: its not necessary to buy a Smart Battery Sense to

make sure a Phoenix Smart Charger stops charging a Victron Smart Lithium Battery

below 5°C.

Add tail current functionality

When the charge current is below the threshold for 1 minute, the absorption stage

is ended and the charger will switch to ﬂoat/storage.

Add high battery temperature condition to programmable relay

Requires temperature sensor, e.g. Smart Battery Sense

Allow 0% recondition current

This ﬁxes an issue with the VictronConnect lithium preset

Setting it to 0% skips the recondition stage, if enabled

Add Keep Alive support

This improves bluetooth connectability, with VictronConnect

Add support for settings changed

Add remark about voltages when charger has multiple outputs

Solar Chargers:

Add ﬁrmware v1.53 update:

Remove improvement, added on v1.52, of the remote voltage sense compensation to

speed up ﬁltering. That improvement is postponed for now.

Fix bugs that caused the MPPT Control to get stuck on “CONNECTING” as well as

“FETCHING HISTORY”. The changes are (a) that text messages are now always sent every

2 seconds and no longer interrupted when a hex message is received; and (b) the History

total data is now always announced together with the history day0 data.

Includes changes in ﬁrmware v1.52:

Include low power mode for the small models. Idle current consumption (when PV is

around 0V) is reduced by around 70%.

Improve remote voltage sense compensation to speed up ﬁltering when necessary

and improve voltage control response.

Change 100/20 48V default battery changed from 48V to auto detection.

Fix remote voltage compensation for small models. The voltage compensation of

small MPPTs did not consider some current depended voltage drops, causing the

MPPT to have a higher voltage setpoint, up to 200mV, depending on the MPPT

current. This FW version ﬁx that.

Add ﬁrmware v3.02 for VE.Can and *.xup based ﬁrmware MPPT models:

Fix bugs that caused the MPPT Control to get stuck on “CONNECTING” as well as

“FETCHING HISTORY”. The changes are (a) that text messages are now always sent every

2 seconds and no longer interrupted when a hex message is received; and (b) the History

total data is now always announced together with the history day0 data.

Fix bug that resulted in the MPPT Control always showing the history of the moment that

the MPPT Control was ﬁrst connected to the MPPT. (Fix announce of day 0 history data)

Includes changes ﬁrmware v3.01:

Change ﬁrmware version number to v3.xx range to avoid confusion between

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

diﬀerent solar charger models.

Improve error 28 trigger conditions.

Improve detection of error 38/39 for 250V models.

Gray out Rx & Tx settings menu entry instead of hiding them when connected via VRM.

Fix trend graphs are not shown in demo MPPTs

Show load output power

SmartLithium:

Add codes to errors and improve error descriptions

VE.Smart Bluetooth Dongle:

Add ﬁrmware v2.26 update

Prevent switching to unsupported baud rates

Support keep alive mechanism

Fix to prevent fragmented responses which could cause failing update over BLE of

attached product

MPPT Control:

Add support for ﬁrmware updates

Add ﬁrmware v1.02 update (mandatory):

Solves MPPT Control getting stuck in “FETCHING HISTORY”. Note that there are also fw

updates for the solar chargers that solve this bug, but for the VE.Can and *.xup based

MPPTs also a diﬀerent —and more prevalent- bug leading to the MPPT Control not fetching

the new history from the MPPT, causing the MPPT Control to always show the history of

the moment the MPPT Control was ﬁrst connected to the MPPT. Because of that, and

because updating an MPPT Control requires the power cable that is supplied with it but

most likely not installed in most applications, we recommend to update the solar charger

ﬁrst; and then only update MPPT Control in case its still having issues.

Makes the communication more robust

MPPT RS:

Add display settings menu

Include temperature unit setting

Inverter RS:

Add display settings menu

Include temperature unit setting

VE.Bus inverter/chargers:

Fix L3 power output shows the value of L2 output

Battery monitors:

Fix battery current can't be set higher than 999Ah on iOS when region is set to Sweden.

2024-09-13 09:45 69/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

v5.33 (Released oﬃcially)

2020-09-30

Changes

Orion Smart:

Add Orion Smart ﬁrmware v1.06 update:

Fix an issue that causes the engine always considered to be shutdown. This issue only

aﬀected systems with engine shutdown detection function enabled and the “Shutdown

voltage” set to a value above or equal to 13.30V when updating to the previous v1.05

ﬁrmware. Systems using default settings are not aﬀected.

v5.32 (Released oﬃcially)

2020-09-23

Changes

Fix “Fetching data” message is shown on the background when the alert notiﬁcation drawer is

open.

Fix connection process gets stuck at 20% when the bonding information is not valid, e.g., after

changing the PIN code from a diﬀerent phone.

Fix default PIN code warning “Do not warn me again for this product” option sometimes is not

applied until the app is restarted.

Improve behavior when a scan is started before the previously product was actually

disconnected

Changes to Trends UI and zoom functionality

Show short note when ﬁrmware library is empty

Fix Lithium Iron Phosphate (LiFePo4) preset for non-MPPT products with equalization auto stop

mode setting support.

Orion Smart:

Add ﬁrmware v1.05:

Add input voltage modulation when input voltage gets below the engine shutdown

detection level (Vshutdown) to avoid depleting the starter battery.

Add new engine shutdown detection strategy to include a delayed start level to allow the

starter battery to recharge for some time after turning on the engine.

Add diﬀerent default input voltage lock-out values for when the charger is at charger

mode (12.5V and 12.8V) or at PSU mode (10.5V and 11V).

Phoenix Smart Charger:

Add remark “History data is for the total of all outputs” to history page (history is only available

in beta ﬁrmware)

Improve charge current setting adding minimum, low, and max current presets. Low current

preset matches the charger low current mode so the charger LEDs behavior is the same than

when enabling by pressing the physical button.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Solar Chargers:

Add support for future MPPT models

Smart Chargers:

Add support for VE.Smart networking (only Phoenix Smart Charger, by using a beta ﬁrmware)

Layout ﬁxes and improvements

Fix reported power supply state

Fix absorption time description

Change the way the adaptive absorption time is displayed, make it similar to the MPPT for more

consistency.

Enabled more battery preset capabilities

Improve re-bulk voltage oﬀset setting

Add “Why is the charger oﬀ?” functionality

Add low temperature cut-oﬀ settings (only supported by beta ﬁrmware)

Add IMPULSE-II Smart IP65 ﬁrmware v3.17

Add Blue Smart IP65 Charger 12/5 ﬁrmware v3.22 update

v5.31 (Released oﬃcially)

2020-09-01

Changes

Fix connection gets stuck showing “Fetching data” when connecting to a Bluetooth dongle in

fault state

BMV & SmartShunt:

Fix issue setting battery capacity to a value greater than 999Ah

Fix missing decimals for mid-point voltage alarm and relay

Smart Phoenix Inverter:

Fix disable Bluetooth function

v5.30 (Released oﬃcially)

2020-08-08

Changes

Fix ﬁrmware updates loop on iOS & macOS when updating products based on .xup ﬁrmware

v5.29 (Released oﬃcially)

2020-08-05

Changes

2024-09-13 09:45 71/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Fix BlueSolar VE.Can MPPT ﬁrmware update via VE.Direct Smart Dongle

v5.28 (Released oﬃcially)

2020-08-03

Changes

Add the date to history CSV exports

Add a setting to keep screen on while using VictronConnect

Improve Bluetooth connection

Allow commas and dots as decimal separator. This is useful on phones/computers with non-

matching locale and keyboard layout conﬁguration.

Fix default battery monitor values when creating a new battery preset

Uniﬁed MQTT and VRM error codes

Added acknowledgment checkbox on the disable Bluetooth dialog.

Fix duplicated disable Bluetooth switch/button

Keep the connecting blur until all the live values are fetched.

Show battery monitor settings in battery presets only if supported by the product

Improve error message shown when opening a settings ﬁle created with an older

VictronConnect version.

Solar Chargers:

Update “Fixed absorption” description text

VE.Bus Inverter/Chargers:

Add ﬁrmware v475

Fix when updating the dongle ﬁrmware, a wrong warning that corresponds to Multi/Quattro

ﬁrmware update is displayed.

Fix VE.Bus product is not recognized after a ﬁrmware update requiring to press the scan button.

Orion Smart:

Add ﬁrmware update v1.04 for Non-Isolated models (mandatory update):

Fix a bug regarding the temperature compensation of the output voltage.

Smart Chargers:

Collapse status widget when scrolling

Add support for future Phoenix Smart IP43 Charger revision 2 models

Fix “User deﬁned” is shown when selecting Lithium preset from VictronConnect presets library

Fix vertical scroll bar in live data page is not shown on desktops and tablets when in landscape

mode

Lynx BMS:

Add Lynx Ion BMS support

Battery monitor:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Fix remaining time shows NaN when soc is lower than the discharge ﬂoor setting value

v5.27 (Released oﬃcially)

2020-07-06

Changes

Improve the warning and information messages in the ﬁrmware update page

Improve troubleshooting information

Show default PIN code to the connection progress pop-up

Advice to check the notiﬁcations bar when the pairing request doesn't appear on Android

Only advice to remove the product from the Bluetooth paired devices list when that could be

the issue.

Disconnect every Bluetooth product before starting a new scan. This prevents the state where a

product could remain connected after an interrupted ﬁrmware update.

Increase the number of lines logged into the service report.

Fix *.xup update fails when triggered within a few seconds after VictronConnect start up.

SmartLithium:

Add ﬁrmware v1.19 update (mandatory)

Fix issue with 12V batteries where cell 2 and cell 3 had a lower voltage when the battery

was not charged for some time. (12V battery model only)

Fine-tuned balancer behaviour

v5.26 (Released oﬃcially)

2020-06-19

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.12 (macOS Sierra) and higher|App Store

Linux AppImage

Please report bugs and give feedback to these betas via the Disqus comments below. Please note that

comments are not public by default, and ﬁrst go to a moderation queue.

Changes

Fix freezes for a small amount of time while retrieving installations from the VRM server

Fix possible crashes after re-scan

Fix Android crashes and synchronization problems

Fix devices in range list doesn't refresh when joining an existing VE.Smart network

Fix settings save/load buttons sometimes remain disabled having to reconnect to activate them

Fix the PIN dialog keeps the input of the ﬁrst PIN change when changing the PIN twice on same

session

2024-09-13 09:45 73/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Remove duplicated demo products

Do not show the default PIN code warning if there is a mandatory ﬁrmware update available

Improve PIN code reset via PUK error handling

Fix PIN code reset via PUK on Linux

MPPT Solar Chargers:

New “charger oﬀ reason” feature: Display the actual oﬀ reason reported by the charger and

oﬀers guidance for troubleshooting possible installation problems. This feature is not available

for the following solar charger models:

BlueSolar 70/15

BlueSolar 75/10

BlueSolar 75/15

BlueSolar 100/15

BlueSolar 100/30 rev1

BlueSolar 150/35 rev1

BlueSolar 75/50

BlueSolar 100/50 rev1

Disable equalization voltage setting when Lithium preset is selected

Rename “ESS” state by “External control”

SmartLihium:

Improve battery status reporting and remove the “Busy” state.

Orion Smart:

Fix battery preset setting shows “Factory default” instead the name of the selected preset

VE.Bus inverter/chargers:

Fix ﬁrmware update button is disabled when forcing Multi/Quattro detection.

Add ﬁrmware v474

InverterRS:

Fix history CSV export

Add SOC and temperature readout to the demo product

Smart Chargers:

Fix wrong voltage limits on demos

v5.25 (Released oﬃcially)

2020-05-25

Changes

Mark the VE.Direct Smart Dongle (Rev1) ﬁrmware v2.23 as a mandatory update. When a dongle

running ﬁrmware v2.10 is connected to a BMV-70x the battery reading current is read only once

and doesn't update when the value changes.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Fix an issue that makes ﬁrmware updates via VE.Direct cable will not use higher baud rates

than 19k2 making the ﬁrmware update slower than it should be.

MPPT Solar Chargers:

Fix an issue that can make the battery voltage settings don't show the 36&48V options when

the MPPT actually supports them.

v5.24 (Released oﬃcially)

2020-05-22

Changes

MPPT Solar Chargers:

Fix a bug that makes battery current readout stop updating

Fix Re-bulk oﬀset setting shows the oﬀset instead the resultant voltage when modifying it. This

issue is only present German translation.

Smart Chargers:

Fix main widget misalignment when in PSU mode and translation text is too long

v5.23 (Released oﬃcially)

2020-05-22

Changes:

Fix history CSV export (Solar Chargers & Blue Smart Chargers)

Fix Multi/Quattro AC Input control battery low voltage condition

Fix battery settings voltages on Orion Smart demos

Fix updater issues when the update button is pressed while the connection is not ready

v5.22 (Released oﬃcially)

2020-05-18

Changes:

Fix new battery presets cannot be created

v5.21 (Released oﬃcially)

2020-05-18

Changes:

2024-09-13 09:45 75/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Improved Bluetooth stability on Android

Fix crash on Android when removing the USB serial port

Performance improvements, mostly noticeable during connection time.

Do not show the disable Bluetooth warnings when connected via VE.Direct cable

VE.Smart network UI/UX improvements

Fix battery presets edition

Improve URL scheme registration on Linux

Fix freezes on macOS where there are Bluetooth devices providing a serial port interface

Solar Chargers:

Add Bluetooth ﬁrmware v2.25

Add ﬁrmware v1.50

Improve PV Short Protection detection for 250V models when on ESS

Add timeout to join a synchronised charging network

Remove error 68. Now, the error will be no longer triggered when the same information

comes from BLE and VE.Direct. A decision method based on priority is applied, where

VE.Direct has a higher priority when compared to BLE. For more information, see MPPT

Error Codes.

Fix spurious charge algorithm reset after overshoot/zero current event.

Add ﬁrmware v1.06 (VE.Can models)

Update error 68 trigger conditions. Now, the error will be no longer triggered when the

same information comes from BLE and VE.Direct/VE.Can. A decision method based on

priority is applied, where VE.Direct/VE.Can have a higher priority when compared to BLE.

Error will still be triggered if same data is received from VE.Direct and VE.Can. For more

information, see MPPT Error Codes.

Improved error 38/39 detection when charger is externally controlled (i.e. ESS mode).

Fixed issue that could lead the MPPT to trigger error 67 (BMS missing) even when the BMS

was present at the network. Also, the error could not be cleared properly.

Change error 67 behavior by turning it into a warning, not error. Output voltage drops to

the battery base voltage.

Fix the reception of the charge current limit. That was a combined issue with Venus OS.

The ﬁx for the Venus is available on Venus OS v2.53 or higher.

Fix NMEA device instance change when done over complex commands on VE.Can.

Show PV power of all the synchronised charging MPPT's in the VE.Smart network

Blue Smart Chargers:

Add ﬁrmware v3.21 update:

Added custom battery settings

Added charge cycle history

Keeps track of the last 40 charge cycles

Keeps track of the cumulative data, like operating time, charged Ah, etc.

Improved Bluetooth connectability

Fixed issue on some Android phones that kept the connection alive when it must be

closed

Show charger as not-connectable (greyed out) in VictronConnect, when it is already

connected to another device

Extend Bluetooth range for Blue Smart IP67 chargers

Improved Bluetooth stability when performing a ﬁrmware update

Changed re-bulk strategy

The charger now automatically jumps back to bulk from (almost) all states if the

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

current demand exceeds the maximum charge current. Previously this was only

possible from the ﬂoat and storage state.

A setting is introduced to set a current threshold for jumping back to bulk (default

disabled). When the charge current in ﬂoat or storage exceeds this threshold value

it will jump back to bulk.

Improved relay clicking when mains is disconnected

VRM:

Fix app crash can happen on Android on reconnection when bringing back the app from

background

Fix error ”-100“ on poor network connections or Venus devices with high CPU loads, now

connection is retried and the error is better handled.

Do not try to get a list of devices when the user has no full control access to the installation.

InverterRS:

Add battery soc readout and battery monitor settings

Add new overview page with current ﬂow lines

VE.Bus Inverter/Chargers:

Hide temperature compensation setting when Lithium battery setting is enabled

Add ﬁrmware v473

Added grid code for Denmark.󰜩(based on “Technical regulation 3-3-1 for electrical energy

storage facilities”)

Added option to limit AC current to/from inverter for the grid codes:󰜩Europe, Belgium,

Austria and Germany.

Added Lock-in/Lock-out on AC input voltage for the Cosϕ function for the grid

codes:󰜩Europe, Belgium and Austria

Phoenix Smart Charger:

Add ﬁrmware update v3.19:

Disable 30 seconds Bluetooth recovery time at power-up

Bluetooth can be re-enabled through VE.Direct or by pressing the MODE button for 10s

Hide re-bulk current setting; not used, but could still be set

BMV & SmartShunt:

Increase displayed battery current resolution

Fix voltage settings limits for BMV-710H Smart

Smart Chargers:

Make the default max bulk time product speciﬁc

v5.20 (Released oﬃcially)

2020-04-06

Changes:

2024-09-13 09:45 77/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Include Linux build as part of the releases

Fix iOS video playback

Make connection retry mechanism stop after three attempts

Fix app can freeze when changing layout by resizing the window

Internal improvements

Speed up ﬁrmware updates for *.dup ﬁrmware based products

Improve alarm notiﬁcations panel

Add connection keep alive mechanism:

Fix that on Android, in certain situations the Bluetooth connection remains active when it

should be closed.

Needs to be supported by the device ﬁrmware, at this moment only supported by Smart

Battery Protect ﬁrmware v2.04.

(New)VRM feature:

Monitor, conﬁgure and update VE.Direct devices remotely.

Android:

Improve scanning by using a new API

Add a dialog explaining the location services permission requirement

Fix random crashes

SmartShunt:

Show PIN code reset option

Add history reset button

SmartCharger:

Improve night mode handling

Make re-bulk current a battery parameter

Fix update notiﬁcation doesn't update when error changes

Add invalid history data error, including advice of how to recover

Make changes to charge cycles history in preparation to upcoming new ﬁrmware version

InverterRS:

Add support for InverterRS

VE.Direct Phoenix Inverter:

Add ﬁrmware v1.21 (mandatory):

Fix for false “No Calibration” error

Add demo for Phoenix Inverter 1200VA 230V

Solar Chargers:

Add missing support for SmartSolar MPPT VE.Can 250/85

SmartBMS CL:

Add support for Smart BMS CL

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Smart Battery Protect:

Update Alarm and Warnings to better reﬂect manual

Add ﬁrmware v2.04 update (mandatory):

Added Charge Protection, which prevents overheating that happened when the product is

installed wrongly, ie. by connecting a charger (e.g. a Multi) to the output. Note that still,

also with this ﬁrmware update, the product is not to be installed in such manner. It is not

designed to handle reverse currents. All currents need to go from IN to OUT. Which also

means it cannot be used in combination with an inverter/charger like Multis and Quattros.

This protection merely reduces the risk of overheating, smoke and ﬁre in case of such

error in the installation- design or -wiring. In detail:

When (output is disabled and) output voltage is 0.5V higher than battery voltage

and internal temperature is above 45 °C, the output will be enabled.

Output will be kept enabled until internal temperature drops below 45 °C for 30

seconds.

All this time E8 is blinking on the display and showing an error in VictronConnect.

Support indication of default Bluetooth PIN.

Support advertising connection state while being connected to VictronConnect.

When changing the PIN, drop the existing bond information, such that user needs to pair

again when reconnecting.

Fix issue with VE.Smart, where communication could come to a halt.

Several internal improvements.

GX devices:

Fix detection of CCGX using old ﬁrmware version

Fix GX device pre-selection on VRM registration

Solar Chargers:

Fix demo of some models doesn't allow to set the battery voltage to 36 and 48 volts

VE.Bus Inverter/Chargers:

Add MultiPlus-II ﬁrmware v471

Fix AC low voltage connect value in demos

Add demo for MultiPlus-II 5000

v5.19 (Released oﬃcially)

2020-02-20

Changes:

Fix crashes might occur after a ﬁrmware update when the continue button is pressed

VE.Bus Inverter/Chargers:

Include ﬁrmware v470 for MultiPlus-II models

Improved PWM driving

2024-09-13 09:45 79/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

v5.18 (Released oﬃcially)

2020-02-13

Changes:

Performance improvements on iOS and at ﬁrst run for rest of platforms.

Fix notiﬁcations drawer don't update the alarm/warning/error description is some cases

Order demo groups alphabetically

SmartSolar VE.Can:

Fix ﬁrmware updating via Bluetooth

GX devices:

Improve Venus network settings layout

Add new icons for Cerbo GX, Maxi GX, Octo GX and MultiPlus-II GX

Solar Chargers:

Change default CSV name to SolarCharger instead of BlueSolar

Smart Chargers:

Add default value to re-bulk current setting to the demo of those models that support advanced

settings

Smart Battery Protect:

Fix load output switch stays at oﬀ position when it should be in on position after pressing cancel

in the deactivation warning dialog

BMV:

Fix Input section is overlapped on BMV demos

SmartShunt:

Add SmartShunt demo products

SmartLithium:

Add 12V 100&150 Ah models

v5.17 (Released oﬃcially)

2020-02-03

Changes:

General performance improvements

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Do not show default PIN code warning when there is a mandatory update available

Fix missing decimal digits and units for trends

Show a warning when trying to use an invalid ﬁrmware ﬁle

GX devices:

Auto select the correct host for the remote console when connected via Bluetooth

Solar Chargers:

Improve StreetLight settings UX

Improve TX port and Load output settings UX

Add support for new models

Blue Smart Chargers:

Do not show advanced settings on demos when not supported by the charger

Phoenix Inverter:

Set 60Hz as default freq. for 120V Phoenix Inverter demos, so that it matches the real 120V

products that also have 60Hz as default

BMV-712

Optimise the ﬁrmware ﬁle format to improve the update speed

No changes related, version is kept as v4.03.

Smart Chargers:

Add re-bulk current setting

VE.Bus Inverter/Chargers:

Include latest ﬁrmware, v469

Add missing name/model description for some MultiPlus models

v5.16 (Released oﬃcially)

2019-12-20

Changes:

Fix GX devices discovery on macOS (UPnP)

Fix Windows 7 is reported as unsupported Operating System

v5.15 (Released oﬃcially)

2019-12-12

Changes:

2024-09-13 09:45 81/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Fix an issue that freezes VictronConnect when connecting to a BMV-712 or SmartSolar and

there is a Bluetooth interface ﬁrmware update available

v5.14 (Released oﬃcially)

2019-12-10

Changes:

Guide the user when a product is not found:

Show a button on the device list page which links to a troubleshoot page with the most

common connection issues.

Make it clear that product is using latest ﬁrmware

Show built-in ﬁrmware if there is a ﬁrmware update available

Advice to remove bond when resetting PIN code by using PUK code; Otherwise, if using an

invalid bond the puk reset process will fail

Add SOC to battery settings so now it is possible to manually set it.

Add storage settings to battery presets

Check device OS and warn if it is not supported by VictronConnect

Do not show default PIN code warning if there is a mandatory update available

Fix trends sometimes don't restore the stored trend views

Do not show the default PIN security warning when there is a mandatory update available

Show devices in the devices list even when connection is not possible because are already

connected to another phone/computer. Compatible devices:

VE.Direct dongles - released in v2.17 for SmartBMV, VE.Direct SmartSolar,

PhoenixInverterSmart and VE.Direct external dongle; released in v2.18 for VE.Can

SmartSolar.

SmartLithium batteries - released in v1.17

Smart Battery Sense - released in v1.04

IMPULSE-II Smart chargers - since v3.09

Phoenix Smart Charger - since v3.08

MPPT Solar Chargers:

Add a text to advice to remove the jumper in VE.Direct port when changing load output

operation mode.

Fix available options on RX Functions for MPPTs. Small models have all 4 options, bigger models

do not have a load output.

Smart Chargers:

Add settings support for IP65 24/13 & 12/25 models

Add ﬁrmware v3.14 for Blue Smart IP22/IP65/IP67 Chargers:

Added option to disable BLE oﬀ recovery time of 30s for security reasons. This means that

for the Blue Smart IP67 Charger a bluetooth killswitch is introduced, because there is no

way to re-enable bluetooth once disabled. For both the Blue Smart IP22 and IP65 the

MODE button can be used to perform a bluetooth reset and re-enable bluetooth.

Phoenix VE.Direct Inverters:

Add ﬁrmware v1.19 update for 800/1200VA models:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Fix for 800/1200VA VE.Direct-Inverters: Power-up fails at a low battery voltage

VE.Bus Inverter/Chargers:

Add ﬁrmware v467 for MultiPlus-II

VE.Direct Bluetooth Smart Dongle:

Add ﬁrmware v2.23. This ﬁrmware was already available for rev2 dongles, this is for the ﬁrst

version of the dongle:

Support for device oﬀ reason when attached to Inverter.

Support apparent power when attached to Inverter.

TX power for advertisement increased.

Add default PIN code detection support.

Bonding info is removed when pincode changes.

Support mA resolution for SmartBMV battery current

Several small stability ﬁxes

Advertising with own product ID started if no successful VeDirect communication was

possible within 20 seconds (fallback to be able to update dongle at all times).

IMPULSE-II Smart IP65 Chargers:

Add ﬁrmware v3.15:

Limit charging below 17.4V:

Trigger a low battery voltage error

Open the output relay

Set the charge voltage to 24V

Limit the charge current to 1A

v5.13 (Released oﬃcially)

2019-10-28

Changes:

VE.Bus Inverter/Chargers:

Update MultiPlus-II ﬁrmware to latest version (v466):

New gridcode for France (VFR 2019)

Two special gridcodes added for AS/NZS4777. These should be used in systems where the

Neutral In and Out are externally tied together.

v5.12 (Released oﬃcially)

2019-10-28

Changes:

Fix ﬁrmware version is not shown in all the cases when the update is completed

Fix “update succeeded” message is wrongly displayed when trying to update using an invalid

2024-09-13 09:45 83/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

ﬁle

Various user interface ﬁxes and improvements

VE.Smart network:

Change the way that a VE.Smart network information is presented:

Show devices that are in range for the connected product

Devices in range signal strength

Smart Battery Sense:

Add ﬁrmware update v1.05

Bluetooth internal and external dongles:

Add Bluetooth ﬁrmware v2.23

MPPT SolarChargers:

Add MPPT Solar Chargers ﬁrmware v1.46:

Update marked mandatory only for SmartSolar as these models are aﬀected by the bug

described below.

Fix bug on the internal temperature measurement that lead to not being able to de-rate

the output current due to a high temperature nor triggering the over temperature

protection. (Bug introduced on v1.30). This bug is only present in SmartSolar.

Make 30 day history in demos more accurate

Add VE.Can MPPT SmartSolar ﬁrmware v1.03

BMV-712:

Add BMV-712 ﬁrmware v4.03 (previously v4.01):

Fix an issue that makes the buzzer inaudible

VE.Bus Inverter/Chargers:

Add ﬁrmware version 465 update

Charger settings:

Add battery temperature compensation setting

Fix “Lithium battery” switch state doesn't reﬂect the actual value of the setting

Change hysteresis for Low DC Disconnect and Restart setting

Fix crash when an invalid ﬁrmware update ﬁle is selected

Add errors notiﬁcation

Smart Battery Protect:

Show the correct icon for Smart Battery Protect 48-100

SmartLithium:

Add ﬁrmware version 1.17 update (previously v1.16):

Add cell under voltage pre-alarm threshold setting

Add support for BMS Pre-Alarm

Add Bluetooth On/Oﬀ support. Caution!! Once Bluetooth is disabled it is not

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

possible to enable it again.

Blue Smart chargers:

Add ﬁrmware update v3.12:

Update for all Blue Smart Chargers: IP22, IP65(exept Blue Smart IP65 Charger 12/25 &

24/13) & IP67

Added BLE on/oﬀ

When BLE is disabled, it will still be temporarily enabled for 30s at power-up. The

user can connect within this 30s to re-enable BLE again, perform a ﬁrmware update

or monitor the device. The connection will remain active when the user connects

within the 30s. When the user disconnects, BLE will be disabled.

Clear bonded devices when the PIN is changed, except the connected device

Advice default PIN

Add BLE reset by press and hold the MODE button for 10s

Disconnect the active device

Restore PIN to default

Remove all bonded devices

Re-enable BLE

Prevent VE.Smart communication from lockup

Add ﬁrmware update v3.11 for Blue Smart IP65XL Chargers 12/25 & 24/13

v5.11 (Released oﬃcially)

2019-09-18

Blog post: VictronConnect 5.9 – Solar Charger improvements and much more

Changes:

Fix VictronConnect could not recover properly after an interrupted bluetooth update of the bluetooth

microcontroller/dongles in our products.

Known issues:

On macOS, a ﬁrmware update of Multis, Quattros or other devices with a VE.Bus port may fail. This

issue was introduced in VictronConnect v5.9. A new VictronConnect version ﬁxing this is expected in

the near future. Meanwhile, there is a workaround.

v5.10 (Released oﬃcially)

2019-09-13

Changes:

MPPT Solar Chargers:

- Fix an issue with the MPPT battery presets created with VictronConnect v5.8 and older. Those old

presets don’t include values for the new settings introduced in MPPT ﬁrmware v1.42. Because of that,

when the user selected and re-applied such “old” preset using VictronConnect 5.9, settings like

2024-09-13 09:45 85/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Adaptive absorption were disabled, while they should be enabled by default.

v5.9 (Released oﬃcially)

2019-09-11

Blog post: VictronConnect 5.9 – Solar Charger improvements and much more

Download links:

iOS: App Store (Pending of App Store approval)

Android

Windows 7 and higher

macOS 10.10 (OS X Yosemite) and higher|App Store

Changes:

General:

Trends tab remembers last selected graphs for certain product family

Improve PIN code change process

Improve information shown when unable to connect to a product

Fix PIN code reset via PUK code interface issues

Fix settings ﬁles buttons could not appear when VE.Direct connected

Fix overlapped text in the Inverter/Charger details page on Windows 10

Show a warning when using Default PIN via BLE

Default PIN code must be always changed to prevent unwanted connections, now we

advise it when default PIN code has not been changed

Firmware updates are no longer mandatory for basic monitoring:

Live data page: This page can be accessed without updating the ﬁrmware unless the

update is highly recommended and marked as mandatory.

Setting pages: To view and modify settings it is always necessary to update the product

to the latest version included in VictronConnect.

Do not allow change PIN code to same code

Update the framework on top of which VictronConnect is built, required to comply with Google

Play Store requirements. This will improve the application performance but adds a drawback:

We have to drop support for old OS versions, see below.

Android:

Add ARM64bit build: Takes advantage of all the power of modern CPUs. This is also required by

Google Play Store.

Drop support for Android versions older than 5.0(Lollipop).

Remove unintentional Android “microphone” and “camera” permissions, they are actually never

user by VictronConnect.

iOS:

Requires iOS version 11 or newer. Oldest iPhone supported now is iPhone 5s.

MPPT Chargers:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Include ﬁrmware v1.42 (v1.43 for some models) for BlueSolar and SmartSolar chargers:

The Lithium battery rotary switch preset has been changed. Absorption time is ﬁxed to 2

hours, and it will not stop on low tail current.

The re-bulk voltage was lowered from 13.7V to 13.4V (for all battery types).

Added four new settings:

Adjustable tail current (changeover from absorption to ﬂoat).

Adjustable re-bulk oﬀset voltage (changeover from ﬂoat to bulk).

Adjustable automatic equalization parameters (current / duration).

Choose between adaptive- and ﬁxed- absorption time. The adaptive mode is the

method that has always been in the algorithm. It adapts the time to the battery

voltage as seen in the morning. The ﬁxed absorption time is what it says it is: a

ﬁxed time. No multipliers related to voltage in the morning. Setting absorption time

to ﬁxed does not disable the tail current mechanism: disable that too to get a 100%

ﬁxed absorption time. Note that we advise to not use ﬁxed absorption times for lead

batteries.

Include ﬁrmware v1.02 for SmartSolar VE.Can:

Synchronized charging with VE.Can. This works the same as with previous models and the

Skylla-i.

Add ESS support. When connected on VE.Can, the VE.Can device instance must be 0. Just

like with the previous BlueSolar VE.Can models.

Add BMS support.

All new battery charger settings: ﬁxed absorption, tail current, re-bulk oﬀset voltage, max

auto equalization time, equalization auto stop and equalization current percentage

Support for the Smart Battery Sense and BMV connected via Bluetooth VE.Smart.

Update built-in presets database to match the new ﬁrmware

SmartShunt:

Add support for new SmartShunt product

BMV:

Fix empty item in the transmitting list is shown in the VE.Smart networking settings page.

Orion Smart:

Add ﬁrmware v1.02

Add engine shutdown detection setting

Fix adaptive mode is not changed when selecting a battery preset

BlueSmart Chargers IP65:

Enable PUK code PIN reset when the product supports it

Bluetooth:

Fix PIN code change button it shown multiple times on some devices

VE.Direct Phoenix Inverter:

Add ﬁrmware v1.17

Add “ECO search time” setting

2024-09-13 09:45 87/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Add option to disable Bluetooth on Smart models

Fix wrong AC output voltage being shown in in some cases

VE.Bus Inverter/Chargers:

Add latest ﬁrmware versions (460 & 463)

VeBusInverter: Reduce minimum DC Input low restart voltage (24V/48V)

The minimum DC Low Restart has been lowered for 24V models from 21.8 to 20.6, and

from 43.6 to 41.2 for 48V models. Not for 12V units, due to hardware limitations.

IMPULSE-II chargers:

Add charge cycles history

v5.8 (Released oﬃcially)

2019-07-18

Notes:

When viewing the permissions of the Android version of VictronConnect, it shows “microphone”

and “camera”. This is unintentional and they are actually never user by VictronConnect. On

Android versions >= 6, the individual permissions can be enabled/disabled and the

“microphone” an “camera” permissions can stay disabled. These permissions are removed in

version 5.9beta2.

Changes:

Inveter/Chargers:

Add settings and ﬁrmware updates for Inverter/Chargers connected via MK3-USB:

Firmware version 459 is included in the app and the correct ﬁle for the connected product

is automatically selected when updating.

Only basic settings are included, Virtual Switch and Assistants are not supported

Only single unit systems are supported

Orion Smart:

Add support for Orion Smart converters

GX devices:

Support Maxi GX and other future GX models

Make possible to connect to a GX device even if the model is not recognised.

Smart Battery Sense:

Include ﬁrmware v1.04 update

Blue Smart Chargers:

Update the link pointing to the manual shown when a ﬁrmware update fails

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Bluetooth products:

Add Bluetooth disable option for products that supports it, available in the product info page

Add instructional videos of how to remove the device pairing, required after a PIN code change

VE.Can MPPT:

Include ﬁrmware v1.02

Synchronized charging with VE.Can. This works the same as with previous models.

Add ESS support.

Add BMS support.

SmartSolar chargers, Smart BMV, Smart Phoenix Inverters & VE.Direct Smart Bluetooth dongle:

Include ﬁrmware v2.19:

Disable bluetooth option

MPPT Solar Chargers:

Settings now scale accordingly to the selected battery voltage

Fix presets can be created with incorrect values from a demo product and therefore when

loading it on a real product makes the charger enter in error mode having to restore settings

and power cycle it.

General:

Fix links on ﬁrmware update result text doesn't work

v5.7 (Released oﬃcially)

2019-05-08

Changes:

Fix PIN code change button is not shown

MPPT Solar Chargers:

Prepare support for future ﬁrmware versions

v5.6 (Released oﬃcially)

2019-05-07

Notes:

There is an issue in this version; the option to change the PIN code is not available. It is ﬁxed in

v5.7.

Changes:

2024-09-13 09:45 89/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Fix ﬁrmware update retry is not triggered when reconnecting after an unsuccessful ﬁrmware

update.

Fix disable Bluetooth toggle is shown twice for some products

Make trends use user selected temperature unit

Fix typos in Dutch and German translations

Internal improvements

GX devices:

Show ﬁrmware version when the GX device is running ﬁrmware >= 2.30

v5.5 (Released oﬃcially)

2019-05-02

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.10 (OS X Yosemite) and higher|App Store

Please report bugs and give feedback to these betas via the Disqus comments below. Please note that

comments are not public by default, and ﬁrst go to a moderation queue.

Changes:

Add support for Phoenix Smart Chargers

Add new features highlight on home screen

Add onboarding, shows to the user a brief description of the available options

Add a button to disable Bluetooth; currently available for:

Smart Battery Protect

Smart Lithium batteries

Smart BMV-712

SmartSolar Chargers (only when updated to v1.40 or newer, which is not publicly

available yet at this moment)

Phoenix Smart Charger IP43

Improve reset pin code by PUK handling

Fix the “user deﬁned” is shown when certain battery presets are selected

Android: Fix crash on devices without Bluetooth

Small GUI ﬁxes and improvements

Fix GX log converter day light saving issues.

Add trend graphics for BMV, MPPT and Smart Battery Sense

BMV: voltage, current, power, consumed amp hours, state of charge, starter battery

voltage, temperature, mid voltage deviation

Smart Battery Sense: voltage, temperature (those two are all this device measures)

MPPT: solar voltage, current & power. Battery voltage & current & temperature. Load

current (for models that have a load output)

It records for max 2 hours; and stops/discards as soon as you disconnect from a device.

Fix typos and improve wording on various pages

Set MPPT low-temp cut-oﬀ setting resolution to one degree; the previous higher resolution was

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

pointless.

Add an option to select Fahrenheit as the unit for temperature. To enable, open the main

VictronConnect menu, click settings. Here you’ll see the version of VictronConnect as well as

the option to change language and temperature unit.

Fix EasySolar-II GX, MultiPlus-II GX and Generic Venus devices are shown as Unknown devices

when discovered over UPnP

v5.4 (Released oﬃcially)

2019-03-08

Changes:

Smart Lithium Batteries:

Add ﬁrmware v1.16 update:

Fix temperature inaccuracies. Between diﬀerent batteries the accuracy of the

temperature measurement varied a lot. In this update; three changes have been made to

ﬁx that:

The battery will, only once, automatically calibrate the temperature measurement

when no balancing have been active for four hours.

Added “Battery temperature oﬀset” user setting, range -10°C to +10°C. This can be

conﬁgured through VictronConnect.

Stabilized battery temperature indication.

So, after updating to this version; the user has can do two things: wait for the automatic

calibration to take place. Or go in and set the Temperature oﬀset immediately. When

doing so; the automatic calibration will not take place.

Enable custom name

Venus devices:

Add Venus device discovery via UPnP:

The device running VictronConnect and the Venus device must be connected to the same

local network.

Can ﬁnd a Venus GX when connected to its built-in access point, useful to open remote

console and conﬁgure network settings.

Available functions are:

Open remote console

Open VRM to visualise data or add the installation to your account when setting it

up.

See the device IP address

Android:

Fix toolbar positioning on devices a with tall notch, for example Google Pixel 3XL

v5.3 (Released oﬃcially)

2019-02-10

2024-09-13 09:45 91/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Changes:

Fix English language is not selectable

Improve Spanish translation

Smart Phoenix Inverter:

Show the correct product icon for 1600/2000VA models

MPPT Solar Chargers:

Include ﬁrmware v1.39 update

Fix units sometimes failing when reset to defaults on a test bench; with a power supply

connected to the PV inputs rather than a real PV array. See MPPT change log for more

details.

BMV Battery monitor:

Fix “Battery starts synchronized” setting. This is a recently introduced feature in the BMVs;

Conﬁguring that feature, #70 START SYNCHRONIZED, on the unit itself worked ﬁne. But in

VictronConnect it was not possible to change that setting. Now it works as it should.

Peak Power Pack:

Fix wrong status is shown: it said `On for thirty minutes`; while it should say `On`.

Add missing alarms

Fix “0V” is displayed in case of an over voltage.

v5.2 (Released oﬃcially)

2019-01-09

Changes:

Fix page device page is not closed after reconnection timeout

New products support:

Smart Battery Protect

Smart Phoenix Inverter

BMV Battery Monitor:

BMV 712 Bluetooth ﬁrmware update v2.14

BMV Battery monitor ﬁrmware v3.10(BMV 70x) and v4.01(Smart BMV) update

Add “Battery starts synchronized” setting

VE.Direct Bluetooth Smart Dongle:

Firmware v2.15 update:

Increased VE.Smart transmission robustness.

Start advertising after 20 seconds when no successful VE.Direct communication was

possible

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

MPPT Solar Chargers:

Add scrollbar to presets list

Fix history totals text overlap

SmartSolar Bluetooth ﬁrmware v2.14 update:

Increased VE.Smart transmission robustness.

Start advertising after 20 seconds when no successful VE.Direct communication was

possible.

Smart Battery Sense:

Add ﬁrmware v1.03 update

Improve Bluetooth range

VE.Bus Inverter/Charger:

Fix overload alarm icon is missing

iOS:

Fix PIN code can't be changed because the keyboard overlaps the “Accept” button: Now clicking

somewhere on the dialog closes the keyboard.

v5.1 (Released oﬃcially)

2018-11-23

SmartLithium

Update included ﬁrmware from v1.12 & v1.13 to v1.15

Add “Allowed-To-Charge minimum temperature” setting

By default it disables charge when battery temperature is below 5C.

Improved Bluetooth connection

Fix SmartLithium disappears from the devices list after disconnecting.

BMV Battery monitor:

Fix an issue that makes BMV disappear from devices list after disconnecting. This issue only

aﬀects to BMV which are conﬁgured for VE.Smart networking.

MPPT solar chargers:

Fix AES time show undeﬁned in the algorithm description

Phoenix Inverter:

Fix AC output setting limits in demo products

macOS:

Fix products on the devices list page are displayed with the default name instead of the custom

name.

2024-09-13 09:45 93/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Android:

Improve ﬁrmware update robustness

v5.0 (Released oﬃcially)

2018-10-09

Changes:

Firmware updating:

Fix issue that can cause VictronConnect get stuck at 93% during a VE.Direct product ﬁrmware

update

MPPT solar chargers:

Added ﬁrmware v1.37 update

Fix Automatic Energy Selector load output mode is not listed (only for SmartSolar)

BMV battery monitor:

Fix time remaining displays “0m” when no current is ﬂowing from or to the battery

v4.9 (Released oﬃcially)

2018-08-23

Changes:

VE.Bus Smart Bluetooth Dongle:

Added ﬁrmware v1.07 update

Fixed an issue that makes the page show no values in some situations

Hide SOC items when battery monitor is disabled

Added missing Multi's model names

Fix issues when connected Multi/Quattro ﬁrmware version is lower than 415.

Warn about minimum ﬁrmware version

MPPT solar chargers:

Added ﬁrmware v1.36 update for 250V models

Load output: User algorithm 1&2 minimum voltage is now 10V for 12V systems.

BMV battery monitor:

Added power value reading to the main page

Fix time to go reported as “Inﬁnite” instead of “0h” when discharge ﬂoor SOC level is reached

Fix high voltage relay setting reports wrong values when editing for a ﬁrst time in the session

Blue Smart Charger:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Show correct value for low current setting in demo products

v4.8 (Released oﬃcially)

2018-07-05

Changes:

Add SmartLithium 24V 200Ah demo

Fix device ﬁltering needs to be set after each scan

Mac:

Fix crash when converting big Venus VRM database ﬁles to XLSX

VE.Bus smart dongle:

Add support for VE.Bus Smart Dongle

v4.7 (Released oﬃcially)

2018-06-09

Changes:

Fix products settings page is empty after automatic reconnection.

iOS:

Improve iPhone X support

Blue Smart Chargers:

Fix test stage not being shown for Blue Smart IP65 chargers

Graph tab: Correct battery percentage in absorption stage description

v4.6 (Released oﬃcially)

2018-05-29

* Android: If you can't open the downloaded ﬁle from the downloads list try using a ﬁle browser.

Changes:

Improve ﬁrmware update robustness

Add Chinese translation

MPPT:

Add ﬁrmware v1.33 update for 250V models

2024-09-13 09:45 95/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Further improve PV Short protection.

Fix in reporting current/wattage/state when the unit is not charging.

macOS:

Fix issue that makes settings ﬁles not being saved if no ”.vcsf“ extension is manually appended

to the ﬁlename.

v4.5 (Released oﬃcially)

2018-04-25

Changes:

Fix French translation for “Switch on before sunrise” in Streetlight settings

Solar Chargers:

Add ﬁrmware v1.32 update for 250V models

Improve power-stage shutdown sequence.

Improve / speed-up PV Short protection and introduce error code 39

Fix PV current value stops updating two minutes after connecting

Fix oldest day record is not exported to CSV ﬁle

BMV battery monitor:

Fix temperature alarm and relay settings are always reported as disabled when Fahrenheit unit

is selected

v4.4 (Released oﬃcially)

2018-03-16

Changes:

Fix custom name max length for non ASCII characters

Add VE.Smart networking settings to demo products

Update translations

Fix hardware failure alarm icon

Fix live data relay icon

Small user interface corrections and improvements

Solar Chargers:

Added ﬁrmware v1.30 update, full changelog in https://professional.victronenergy.com

Added internal bluetooth ﬁrmware v2.12 update

Add VE.Smart Networking support

Add low temp cut-oﬀ setting, prevents damage in lithium batteries by disabling the charge

during low temperature conditions.

Show battery temperature when available.

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Temperature is only available when the MPPT is conﬁgured in a VE.Smart network where

the battery temperature is available.

Make auto equalization interval the only charge setting that can be modiﬁed when a factory

default battery is selected

Send local time to the MPPT: Helps streetlights functionality to synchronize.

Fix a bug that keeps streetlights on after sunrise

Issue occurs when the “At sunset” setting is modiﬁed when the “At sunrise” setting is

already set to “Switch on before sunrise”.

BMV battery monitor:

Added internal bluetooth ﬁrmware v2.12 update

Added support for VE.Smart Networking

Fix mid-point deviation unit, it was “V” when it should be ”%“

SmartLithium:

Added ﬁrmware v1.12 update

Add “Allowed-To-Discharge cell voltage” setting

Fix low cell voltage alarm

VE.Smart dongle:

Added ﬁrmware v2.12 update (only for rev2 units)

Added support for VE.Smart Networking

SmartBatterySense:

Added ﬁrmware v1.02 update

Added support for VE.Smart Networking (Voltage & Temp)

PeakPowerPack:

Show conﬁrmation dialog before switching to hibernate

v4.3 (Released oﬃcially)

2018-02-08

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.10 (OS X Yosemite) and higher|App Store

Changes:

Fix duplicated error message when loading an invalid settings ﬁle.

Allow restoring settings from ﬁles created with previous VictronConnect versions

SmartLithium:

2024-09-13 09:45 97/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Disable false low cell voltage alarm

Rename battery to voltage in right panel

MPPT Solar chargers:

Fix save/load settings functionality on BlueSolar 150/100 model

Add relay state to live data page

Add an error in one of the history records of the demo products

Rename load output to virtual load output on devices without load output

Add description to day/night detection settings

History graphs:

Hide Bluk, Absorption or Float segments when the state was not reached

Improve bar length on days without production

Add scrollbars

Add mouseover to bars and buttons

Fix daily records values are partially hidden on some small screens, for example iPhone 5

& iPhone SE

Fix text overlapping due to translations

Phoenix Inverters:

Fix save and load settings icons are disabled when using VE.Direct cable

Add mode setting, mode now can be switched between on, oﬀ and ECO

Add support for future models

Add ﬁrmware v1.14 update for 800VA models

Blue Smart Chargers:

Improve Bluk state description when Li-ion battery is selected

Windows & Mac:

Add scroll bars to device list and settings pages

Add mouseover eﬀect to the refresh button in the device list page

Rename “CCGX log converter” to “Venus log converter”

v4.2 (Released oﬃcially)

2018-01-07

Download links:

iOS: App Store

Android

Windows 7 and higher

macOS 10.10 (OS X Yosemite) and higher|App Store

Changes:

Windows: Fix auto-update of VictronConnect

iOS: No changes

macOS: No changes

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Android: No changes

Note that in v4.0 and v4.1 the auto-update was not working in Windows hence ﬁxed in v4.2, so

Windows users will need to manually download and install this new version. There is no need to ﬁrst

uninstall it; simply download the new version and install it. This will automatically replace any existing

install.

v4.1 (Released oﬃcially)

2018-01-07

Changes:

MPPT Solar Charger history page:1.

Fix on historical graph, PMax is displayed in 'kWh' instead of 'W'1.

Fix yield counter reset button missing2.

BMV2.

iOS only: ﬁx pressing the plus and minus symbols on the clear value also changed the set1.

value at times when it shouldn't.

Fix Tail current is shown as if its in Amps (current), while actually it is in percentage.2.

Fix discharged & charged Energy units mix up3.

Fix Missing “Sync to 100%” and “Zero current calibration” buttons4.

Windows & macOS:3.

Fix device settings windows for the BMV are all blank.1.

Fix saving mppt 30 day history to csv doesn’t work.2.

And our thanks to Damon, Claudio, Justin, Rob, Andre, and others that helped ﬁnd those bugs so

quickly after the release.

v4.0 (Released oﬃcially)

2018-01-05

Changes:

Completely redesigned user interface

Context help for some settings

Improved user experience

Smoother navigation

Tablet layout

Responsive layout on desktop platforms

Orientation locked to portrait on phones, and MPPT history can go fullscreen & landscape.

Added translations: Dutch, French, German, Italian and Spanish. By default the system

language is chosen

Improve ﬁrmware update robustness when updating through VE.Direct

SmartLithium:

2024-09-13 09:45 99/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

New ﬁrmware update v1.07

Internal improvements

MPPT solar chargers:

Improved history page with graphs

Added user battery presets library

Included ﬁrmware v1.29 update

Show the actual state when performing an automatic equalization

Android:

Minimum required version is Android 4.1

Dropped support for Android ARMv5

Notify that the location services are disabled when needed (Bluetooth & Android > 5) and guide

the user to the Android location settings page.

Improved USB OTG connection, ﬁxes ﬁrmware update failures and random crashes.

Fix ﬁrst connection attempt after introducing the PIN code fails

Windows:

Dropped Windows XP & Vista support, minimum required version is now Windows 7. The

previous version, which can be used on XP, will remain available on our software downloads

page.

macOS:

Minimum required version is now Mac OSX 10.10 (Yosemite)

v3.3 (Windows only)

2018-01-05

Changes:

No changes added, this is a transition version to prevent VictronConnect being updated to v4.0 on

Windows XP / Vista.

Windows XP / Vista:

This is the latest version as support for XP / Vista is dropped in v4.0.

Windows 7 and higher:

When updating from v3.2 this version will be installed and v4.0 update will be automatically

requested.

v3.2 (Released oﬃcially)

2017-08-14

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Changes:

* Always show “Restore factory defaults” button when supported. Button is not shown when

VictronConnect doesn not support settings ﬁles for the product. * Enable manual ﬁrmware updates for

Bluetooth products. * Show “Stay close to the device” when updating bluetooth connected devices

Windows & Mac:

Fix command conﬁrmation dialog, command is not sent when accepted. This issue aﬀects

“Restore default settings” button on all products and “Store settings” for Phoenix inverters.

BMV:

Fix save/load settings buttons not displayed on BMV700

Settings ﬁles:

Add support for the new SmartSolar 75/10, 75/15, 100/15, 100/20, 100/30, 100/50, 150/35 &

150/100.

Demos:

Add SmartSolar 75/10, 75/15, 100/15, 100/20, 100/30, 100/50, 150/35 & 150/100 to the demo

library

Blue Smart Chargers:

Fix low current mode toggled when opening app from background. If the app is connected to

the charger, the charger is in low current mode and the app is sent to background and then

opened again the low current mode toggles to normal mode.

Show the proper ﬁrmware error messages when the update fails

Improve ﬁrmware update error message including a link to Victron Live troubleshooting.

Include ﬁrmware v3.0 update.

Internal improvements

For some models the update might take a little longer, as the the hardware shuts down

and it takes a little while to recover from this (approx. 10-15 seconds).

v3.1 (Released oﬃcially)

2017-08-01

Changes:

Add settings ﬁles feature. This enables saving the product settings to a ﬁle and then load it later

in the same or another product. Besides this, a setting ﬁle can be also opened as a demo and

use it for diagnosis as it contains a snapshot of the product at the moment the ﬁle was saved

including history records.

Add demo products feature. A demo product can be used to:

Learn and show the options available for diﬀerent products.

Create a speciﬁc setup, save that and send it to a customer so they can put it in their

device.

2024-09-13 09:45 101/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Besides loading products from the standard library, it is also possible to load it from a

saved ﬁle.

Use this to review settings made to your installations, make changes and then send them

to whoever is at the site so they can apply them.

Allow ﬁltering of the device list

Change menu items width to page width

Feedback when a setting is correctly stored in the device

Fix “Unsupported ﬁrmware version” error when opening BlueSolar & SmartSolar demos

Fix “Show PIN code” option on PIN code change page

Fix “Show PUK code” option on PIN code reset page

Windows & Mac:

Left panel: Improve position of the connected product

BlueSolar & SmartSolar MPPT chargers:

Fix automatic equalisation interval setting is disabled when “Use default charge settings” is

selected

Add an option to disable the charger.

Include ﬁrmware v1.27 update

Add StreetLight night and day detection delay setting

Add inverted load on/oﬀ mode for Rx port function

Remove automatic battery voltage detection option:

Automatic battery voltage detection is only done once @ power-up. If the battery voltage

is present (>7V) the detected battery voltage is stored and further automatic detection is

disabled. If the battery voltage is absent (<7V) the unit operates as a 12V model,

automatic detection remains active (@ next power-up).

Add manual equalization for some models. Excluded models:

BlueSolar 75/50

BlueSolar 150/35 rev1

BlueSolar 75/15

BlueSolar 100/15

BlueSolar 100/30

BlueSolar 100/50

BlueSolar 75/10

Blue Smart Charger IP22:

Fix an issue that disables night mode or low current mode when reconnecting

SmartLithium:

Enable reset PIN by PUK code

Android:

Fix text ﬁeld, dialogs and buttons rendering issues on devices running Android 7

Windows & Mac:

Left panel: Improve position of the connected product

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

v3.0 (Released oﬃcially)

2017-07-05

Download links:

iOS: App Store

Android ARMv7

Android ARMv5

Android x86

Windows XP and higher

Mac OS X 10.8 and higher

Changes:

Add manual ﬁrmware updates for Bluetooth

SmartLithium batteries:

SmartLithium ﬁrmware v1.06 update:

Fix a problem with internal communication

Rename “Communication error” to “Internal communication failure”.

v2.9 (Released oﬃcially)

2017-06-13

Changes:

SmartSolar 250/85 & SmartSolar 250/100 ﬁrmware v1.25 update:

Bug-ﬁx in the mppt tracker control: unexpected drops in energy harvest during a sunny

day

Parameter change: maximum panel current increased from 50A to 70A

v2.8 (Released oﬃcially)

2017-05-16

Changes:

Windows & Mac

Fix an issue that makes that in certain conditions the latest edited setting is not sent to the

product when leaving the settings page.

MPPT Solar Chargers:

Include ﬁrmware v1.24 update for Smart Solar 250/100 and 250/85

Bug-ﬁx in the battery voltage setting: the voltage always read as AUTO even if it is

manually selected. Keep in mind that updating the mppt 250/100 or 250/85 from

2024-09-13 09:45 103/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

v1.23 to v1.24 will change the voltage setting to 'AUTO', make sure to set the

battery voltage to the correct voltage after updating.

Phoenix Inverters:

Improve live data page

Set minimum value for “ECO minimum wake-up power” setting to 15W.

v2.7 (Released oﬃcially)

2017-04-25

Changes:

MPPT Solar Chargers:

Include ﬁrmware v1.23 update

v2.6 (Released oﬃcially)

2017-04-20

Changes:

Improve ﬁrmware update robustness

MPPT Solar Chargers:

Include ﬁrmware v1.20 update

v2.5 (Released oﬃcially)

2017-04-18

Changes:

Android:

Fix devices not listed on some HTC phones (and maybe others)

General:

Add support for 120V VE.Direct Phoenix Inverters

Add support for future new products

v2.4.2 (Android only, Released oﬃcially)

2017-04-03

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Changes:

Fix ﬁrmware update issues on Android 7 devices

v2.4.1 (Android only, Released oﬃcially)

2017-03-28

Changes:

Improve ﬁrmware update robustness

v2.4 (Released oﬃcially)

2017-03-24

Changes:

VE.Direct Bluetooth Smart dongle:

New ﬁrmware update v2.10

Improved communications robustness

Add support for new VE.Direct dongle

SmartSolar MPPT:

Show the correct icon when updating bluetooth ﬁrmware

Fix battery voltage can't be set to 48V on some models

New Bluetooth ﬁrmware update v2.10

SmartLitihum batteries:

Fix cell numbering on live data page

New ﬁrmware update v1.05

Phoenix Inverter:

Fix a typo in temperature alarms

Peak Power Pack:

Rename “Mover” to “High current output(mover)” in live data page

v2.3 (Released oﬃcially)

2017-01-20

Changes:

General:

2024-09-13 09:45 105/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

SmartLithium batteries:

Add new models

BlueSolar & SmartSolar MPPT:

Streetlight: Increase time oﬀset limits from 720 to 900 minutes

Add absorption time limit setting

Phoenix Inverter:

Fix a typo in live data page

v2.2.2 (Released oﬃcially, Android only)

2016-12-06

Changes:

Fix Google Play ﬁltering issue that made some compatible Android devices appear as not-

compatible. Some of the aﬀected phones, but not all:

LG L90

LG Magna

Samsung Galaxy A3

Some variants of Samsung Galaxy A5

Huawei P8

v2.2 (Released oﬃcially)

2016-12-02

Changes:

General:

Add custom names for Bluetooth products, can be set on the product info page

Add support for future products

Show hardware version(if available) on the product info page

Android:

Improve compatibility with Android 6 devices

Keep ﬁrmware update running in background when a phone call is received during a ﬁrmware

update.

Improve compatible devices ﬁltering on Google Play Store specially with some Android 6

devices. This improvement involves the use of the new Android 6 permission system which

makes necessary to request access to device location services to be able to scan nearby

bluetooth low energy devices. You must allow VictronConnect to access to the location services

when requested if you want to ﬁnd bluetooth products.

BMV:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Show relay state (Open/Closed) on the live data page

Phoenix Inverter:

Add overload, DC ripple and low/high AC voltage alarms.

Include ﬁrmware v1.09 update

Blue Smart Charger IP67:

Include ﬁrmware v2.07 update

Use the same page layout than Blue Smart Charger IP65

v2.1(Released oﬃcially)

2016-10-31

Changes:

General:

Increase robustness in case of VE.Direct communication errors

Add support for future products

Android:

Fix serial port communication errors on Android 6 (OTG + VE.Direct USB cable)

BlueSolar MPPT:

Fix a bug on streetlight settings page that made lights don't switch oﬀ till sunrise when PWM is

disabled and “At sunset, switch lights on for a ﬁxed time” is selected.

Add constraints to the day/night detection voltages to make sure that night detection voltage is

never below the minimum detectable voltage

v2.0 (Released oﬃcially)

2016-08-30

Changes:

General:

Add reset PIN code by entering a PUK code. This option is accessible by doing a long press on

the desired product on the discovery page, right click on desktop. This feature is only available

on some products.

CCGX log to xlsx: Include units in column

Android:

New VE.Direct Smart bluetooth dongle ﬁrmware version 2.09 (ﬁxes issues with Galaxy S5 and

probably many other phones)

2024-09-13 09:45 107/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Improve updating and connecting for Android 6

Fixed BlueSolar MPPT 30 day history records are not displayed on Android 4.3

BlueSolar MPPT:

New v1.19 ﬁrmware update included as a mandatory update.

Add a switch to enable/disable equalisation, no need to set equalization values to 0 anymore.

Add temperature compensation setting. Check VictronConnect manual to know how it works:

https://www.victronenergy.com/live/victronconnect:start#bluesolar_mppt

Fixed a bug that made the streetlight functionality stop working after toggling the on/oﬀ switch.

The problem was that the “Switch lights on at sunset” event is disabled when streetlight

functionality is set to oﬀ but it is not enabled again till the “At sunset” setting is modiﬁed by the

user. This ﬁx also detects if the issue is present on the conﬁguration and automatically ﬁxes it

when opening the streetlight settings page.

Blue Smart Charger IP65:

Improved page layout on desktop platforms

New v2.03 ﬁrmware included:

Reduce connection problems, esp. in combination with Android 6

Fixes issues with Galaxy S5 and probably some other phones

Added identiﬁcation: LEDs blink for 2 seconds when connecting

Add support for future Blue Smart Charger models

v1.9 (Released oﬃcially)

2016-07-20

Changes:

General:

Add support for future products

Phoenix Inverter:

Hide “Low battery shut down” setting when dynamic cutoﬀ is enabled.

BlueSolar MPPT:

Make possible to select 36 and 48V battery voltage on BlueSolar MPPT 150/35 rev2

BMV:

Include BMV-70x ﬁrmware v3.08 update

v1.8 (Released oﬃcially)

2016-07-04

Changes:

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Phoenix Inverter:

Include Phoenix Inverter ﬁrmware v1.03 update

Fix Phoenix Inverter “Low battery shutdown voltage” setting is locked and showing “Dynamic”

v1.7 (Released oﬃcially)

2016-06-29

Changes:

General:

New functionality: Convert CCGX log ﬁles to .xlsx Excel sheet (only Windows & Mac OS X)

New functionality: Export 30-day BlueSolar MPPT history as CSV

New functionality: “Create service report” option generates a diagnostics report for sending it to

Victron Energy service in case of any issue.

Improve dialogs, now all the dialogs are better centred on the screen

Android: Shorten connecting time during updating

Fix an issue that makes necessary to scan several times before Peak Power Pack is shown on

the devices list when using VE.Direct USB interface(issue introduced in VictronConnect v1.6)

Fix issue that makes one of the Accept/Cancel buttons sometimes doesn't appear on iOS dialogs

Remove some unused icons, now the install size is sightly smaller on iOS

BlueSolar MPPT:

Send local time to the MPPT when accessing to the streetlight settings and when switching on

streetlight function. This makes the streetlight timer works more accurately prior to the

synchronisation with the solar activity.

Streetlight: Don't hide sunrise options when “Switch on till sunrise” is selected

Load settings: Add boundaries for high and low voltage levels

Battery settings: Make possible to set equalisation voltage to 0V

Phoenix Inverter:

Add dynamic cutoﬀ settings (dynamic cutoﬀ will be available on the next ﬁrmware, v1.04)

Peak Power Pack:

Fix size of the icon shown in the live data page

VE.Direct Bluetooth Smart dongle:

Include new ﬁrmware update v2.07 that improves compatibility with Android 6*

*Tested phones

The following phones are tested and working but the update should also ﬁx compatibility with many

other Android 6 phones.

Sony Xperia Z5

Motorola Moto G 2014

2024-09-13 09:45 109/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

HTC One M9

Samsung Galaxy S5 [1] [2]

[1] There still one issue that randomly makes the connection fail, to make it work again

disable/enable bluetooth.

[2] To make it easier we recommend to use another phone to update the dongle ﬁrmware but is also

possible to use the Samsung phone to do it, then some extra steps are necessary:

Remove the dongle from the paired devices list on the phone bluetooth settings1.

Close VictronConnect2.

Disconnect the dongle from the VE.Direct port and connect again while pressing the clear PIN3.

code button to start the dongle in boot loader mode. Blue and red LED's will blink alternatively.

Open VictronConnect and click on the dongle item and start the update process4.

After entering in boot loader mode you have 30 seconds to connect to the dongle before it goes back

to the normal mode. Start the process from step 1 if something fails. After the dongle is updated you

might have to disable and then enable bluetooth again.

v1.6 (Released oﬃcially)

2016-06-10

General:

List unrecognised Victron products the device list page. Useful when running an outdated

VictronConnect version with new products.

BlueSolar MPPT:

Fix “Use default charge settings” item behaviour when switching the rotary switch while battery

settings page is displayed.(Only aﬀects to MPPT with rotary switch and fw v1.17)

Include BlueSolar MPPT ﬁrmware v1.17 as mandatory update

v1.5 (Released oﬃcially)

2016-05-02

Fixed PIN code change function

v1.4 (Released oﬃcially)

2016-04-27

New feature: Manual ﬁrmware updates. Manual ﬁrmware update option available on the product

info page. Users with a BlueSolar MPPT can test this feature with the new v1.17 ﬁrmware

available on https://professional.victronenergy.com.

General small bug ﬁxes and improvements

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

iOS:

Fix issues with dialogs displaying long messages.

New ﬁrmwares included on this version:

Phoenix inverter 250 and 375 VA fw: v1.02 (mandatory)

VE.Direct Bluetooth Smart dongle fw: v2.06(mandatory)

Fix issue when connected device update was interrupted, resulting in device not being

seen by VictronConnect

Show both leds when there is no vedirect device

v1.3 & 1.3.1(iOS) (Released oﬃcially)

2016-03-31

New feature: Firmware updates. Firmware updates are included inside VictronConnect, when

connecting to a product with a new ﬁrmware available the update page will pop up.

Included ﬁrmwares on this version:

VE.Direct Bluetooth Smart dongle fw: v2.05 (mandatory*)

BlueSolar MPPT VE.Direct fw: v1.16 (mandatory*)

Phoenix inverter 250 and 375 VA fw: v1.01 (mandatory* and ﬁxes bug in changing low

battery settings)

Phones/Tablets

Fix the app state handling, now VictronConnect disconnects from the product when the app is

sent to the background or when receiving a call.

Android

Improved USB OTG support on Android 6 (Marshmallow)

BlueSolar MPPT

Added total yield (system and resettable) to the history page.

Remove white space displayed on history records for MPPT without load output

BatterySettings: Only supported voltages are displayed.

Fix an issue that sends the voltage values automatically when entering to the battery

BMV

Correct maximum starter battery voltage on history page

Phoenix inverter

Fix wrong product name displayed

iOS: Fix product info page doesn't open

Change power bar color to red when the nominal power is passed

Display a warning box notifying that the “Store settings” button should be pressed to make the

changes permanent

2024-09-13 09:45 111/112 VictronConnect changelog and beta releases

Victron Energy - https://www.victronenergy.com/live/

Known issues:

iOS: Wrong splash screen during launch(ﬁxed in v1.3.1)

* Products with ﬁrmware updates marked as mandatory should be updated to continue using

VictronConnect

v1.2 (Released oﬃcially)

2016-03-03

New platforms: Windows and Mac OS X versions are now available.

Add action bar to iOS keyboard with a minus (-) button and a “Done” button

Fix “Clear history” button on MPPT and BMV

Use diﬀerent name in each step during the bluetooth dongle ﬁrmware update. (VE.Direct BLE

dongle (legacy) and VE.Direct BLE dongle 2 (legacy))

Show Bluetooth/VE.Direct icon depending on the connection type.(Android and MacOS)

BMV

Fix an issue that returns a wrong value by setting to zero the alarm/relay temperature settings

Fix typo in temperature warning message shown on the live data page

Improve max/min values handling on alarms/relay settings pages

BlueSolar MPPT

Show description of the selected load mode algorithm

Fix “Clear history” button: it was partially hidden on the history page

Auto scale yield and consumption unit on the history page from kWh to Wh

Allow negative values for midnight-point shift on streetlight settings

Add load current to the live data page

Fix information box that warns the user that 30 day history is only available since ﬁrmware

v1.16.

Known issues:

Values doesn't ﬁt controls on systems with the default font size set to large. The temporary

workaround to ﬁx the issue is to set the system default font size to normal. (Mac & Windows)

Phoenix Inverters:

250VA Inverter is displayed as 375VA

375VA Inverter is displayed as 250VA

24V and 48V devices: In combination with Inverter Firmware 1.00 the (alarm) low battery

voltage thresholds are displayed wrong and cannot be modiﬁed correctly. However the

thresholds used by the Inverter are the correct ones, as listed in the user manual of the

inverter. Solution: upgrade Inverter SW version to 1.01 or (newer).

On iOS only, clicking to the “Product info” button doesn't open the info page.

v1.1.5 (Released oﬃcially)

2016-02-02

Last update: 2024-09-12 11:23 victronconnect:beta https://www.victronenergy.com/live/victronconnect:beta

https://www.victronenergy.com/live/ Printed on 2024-09-13 09:45

Fix BlueSolar MPPT streetlight settings. In versions v1.1.0 up to and including v1.1.4 it seemed

like the streetlight settings were stored correctly, but they were not.

VE.Direct BLE dongle renamed to VE.Direct Bluetooth Smart dongle

Known issues:

On iOS it is not possible to set a negative value. Only a problem for BMVs when setting relay

and alarm thresholds for temperature.

v1.1.4 (Released oﬃcially)

2016-01-28

Add support for VE.Direct BLE dongles.

Always go back to device main page on disconnection

Fix consumption scale for BlueSolar MPPT history records

Improve dialog style under iOS

Improve appearance on small screens (<4”)

Correct TextField font

Disable settings button while connecting

Fix PWM information box in the streetlight settings page

General small bug ﬁxes and improvements

Add new MPPT SmartSolar products

Improve Blue Smart Charger page on small screens

Update settings values immediately when restoring to defaults

Fix “-0Ah” values for the BMV “Consumed Ah”.

DISQUS

~~DISQUS~~

From:

https://www.victronenergy.com/live/ - Victron Energy

Permanent link:

https://www.victronenergy.com/live/victronconnect:beta

Last update: 2024-09-12 11:23